It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I know it possible for a nrf24l01+ configured as RX to receive communication from several nrf24l01+ configured as TX. (because RX has 6pipes.) I tested and that works...
Hi,
Loaded SDK8 S110 softdevice and application to nRF51822(pca10001), then the application works well. When I want to reload the sofedevice by nRFGo, I get the error message...
Working on a remote monitoring system.
Ethernet solution is on the table now.
But it needs to have extra chipset on board to do so.
I haven't had a chance to look into...
Is there any way i can get UTC time?
Is there any real time clock which keeps track of the time even if the chip is off?
I am using nrf51822 and require the UTC time...
Hey everyone,
I'm having problems with my app's ram usage as you can see from my previous questions.
I've tried this little piece of code:
void memcheck(void){
...
hello friends,
Im developing an application where im trying to connect a central and a peripheral but since the signal strength depends upon run time environment i am getting...
The App ~ BLE Stack is the device, Central is smartphone.
is correct?
I don't understand this sequence.
Do not adv_data_set and the adv_start before the scan?...
I'm attaching a function where I use the sd function :
void edit_speed_ID(uint8_t speed)
{
uint32_t value;//, err_code;
value=5 * speed;
while(sd_flash_write(address...
Unfortunately it seems my post devzone.nordicsemi.com/.../ has been lost.
This is a re-post.
I am trying to manipulate Flash data in CODE_SPACE one page at a time. Currently...
I'm using nRF51822 for ble.
For my application, I need to increase rf power.
( My application needs +10dBm)
In case of CC2540(TI ble chip), there is application note...
Hello,
I have 2 nRF51822 with S130. One is central, the other is device.
I want to exchange custom data between these 2 devices after connection. What is service best...
Hello,
I do communications between 2 nRF51822 (one central and one device). Once they are connected, cant i do a kind of deep sleep and freeze stack state for 1 minute...
I'm getting a hardfault on some float operations that I wasn't getting before I upgraded to SDK 6.0.0 and SD 7.0.0. At least, I wasn't getting them at all before that and...
Hi:
I use spi0(0x40003000) to wirte data to external flash(W25Q64) with SD8.0(sdk8.0.if I write data without sd, it is OK), and when program run to rx_data[number_of_txd_bytes...
