hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
When initially starting Sidewalk on BLE it seems that the current consumption is high if you start with only LINK1 enabled. It seems that perhaps this is due to the SX1262...
I am using Wireshark 4.4.0 and Nordic nRF Sniffer for Bluetooth LE 4.1.1 (nRF52840-Dongle PCA10059). In Wireshark I see a device, a peripheral, sending advertising packets...
hey, I am using nrf52840 in that i am making it compatible with DFU by using sdk2.8, but getting this error
C:/ncs/v2.8.0/nrf/include/flash_map_pm.h:47:22: error: 'PM_mcuboot_secondary_ID...
hello!
I am currently using the nRF7002DK to implement the examples from nRF dev academi. I am practicing based on lesson 5-exercise 2.
lesson 5 exercise 2
In the example...
Hello, I want to make my project DFU OTA compatible, so when I tested on development it works fine once I created my pcb using nrf52840 module in it. So it is taking huge...
Hello,
I have a question regarding a recent issue.
I'm currently developing with the nRF52840 IC or EVM, and I'm facing a problem. Whenever I write firmware to the flash...
Hi Team,
I recently purchased 2 Audio DK's and I set one up as a gateway and the second as a left headset. I was able to pair the two, stream audio from my PC through the...
Hi,
We are currently developing a BLE device (HW and SW) using the NRF52811.
As we want to be able to update the device via FOTA we need to have the Bootloader to have...
Hello,
I am trying to upgrade my project from ncs 2.1.0 to ncs 2.6.1. I am running into some strange issues with mbedtls and I suspect it's because the same ciphers enabled...
Hi All,
We're going through BQB certificate with our mice, and we're informed that test get failed because new rule will be implemented in May 2023.
Our Chip is NRF52833...
Hello,
I want to use external flash. I did some research on the subject. I am using SDK 2.6.1. I have a few questions.
1- Does the spi_flash example I examined work on...
I have a custom nRF9160 board running a modified asset_tracker program. I am using UART0 as a command line interface for testing and debugging. I can enter commands to setup...
Hello. I'm trying to do spi communication on a custom board with nrf5340 used. I'm using three threads, I build it, but if I put it on the board, the board will have a problem...
Hello I’m using the NINA-B306-00B BLE module which uses the nRF52840 MCU for a custom board application. The BLE module interacts with two sensors, an accelerometer via SPI...
