Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hello, I want to purchase cables to connect a Flasher Pro (cable should end on DB20 Female) to an nRF52-DK onto "Debug In" connector (cable should end on mini DB10 Female...
Hello, I am developing a solution based on nrf52-DK, using nRF52832.
I am trying to use JFlash to read Device Serial Number. I could read it with JLink , with command "mem32...
Hi, hope someone can help me.
The past 3-4 years I have used SDK 17.1.0 and SES for SW development where the SW is running on a nRF52840 SoC which is the heart of our product...
I'm working on a Docker image that includes a VS Code server for the purposes of workshops and training, and I'd like to install the nRF extensions (e.g. https://marketplace...
hi，bro
I want to support both BLE and GZLL simultaneously and perform the corresponding initialization work based on the value of a variable, mode . However, when I set...
Hi,
I have difficulties to sniff BLE packets with nRF52840 and wireshark between a remote controller and phone.
I can capture all the pairing process, I see DHKey exchange...
Greetings!
I am looking into Bluetooth Mesh, and the allowed radiated power according to Norwegian law. The general limit for 2.4GHz is 10mW, but if we utilize FHSS the...
Hello, I'm running into an issue with the "modem shell for NR+" application on a pair of nrf9131ek evaluation kits. The local sales rep. suggested that I reach out to Nordic...
Hello, I have a pair of nRF9142EK devices that I've been using to test DECT NR+. Now, I'd like to test out one of the boards with the cellular modem firmware for nRF9131EK...
Hi Support team,
I am using nRF9160 module and i want run two server on the module, one is modbus server and other is CoAP server. so is it possible to run both server...
When using the adafruit feather nrf52840 , the lowest I can seem to get power usage is around 400uA (including with the boards/nordic/poweroff sample ) .
This is my device...
Hello
I'm exploring the mesh dfu transfer, get some strange results
Here is the setup
1 distributor, 1 target
On the distributor I start the transfer with mesh models...
Hi,
I need to setup shell interface on both sides to exchange sensor data via uart.
The connection is as follow: cable 1: nRF52840DK Pin (TX - P1.02) → nRF9160DK Pin...
