Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello,
I have an issue where my PC suddenly can't use any JLink after it had previously been working. Nothing changed to my knowledge that would have caused this issue other...
Hello,
I'm trying to enable the Power management for nRF9161 over nRF-Connect SDK2.5
the prj.conf has an entry of 'CONFIG_PM=y'
but it not accepted because we do not...
I've received a Nordic Semiconductor nRF9161 from a friend, who has been using it for a while.
I would like to completely reset the module, as it came when bought, so...
Im trying to use the BMA4xx driver (via i2c) in 2.7.0. The driver seems to init the device ok but I am getting a "SECURE FAULT" as soon as I do a sensor_sample_fetch . Attached...
Hi,
I spend few day trying to understand the issue with the provided sample (followed the tutorial) in the IoT fundamental lecture for the MQTT protocole. Then, I tried...
Hardware: nRF52840 (Custom Hardware)
Software: nRF Connect SDK v2.6.1
I am using the nRF52840 with custom hardware, where the device operates in two modes: Sleep Mode...
Hi,
In my project, I need turn on/off the hfxo, I found when i configure the hfxo, the nfc is not working. Here is my code:
void gps_server_function ( void * p1 , void...
HW: NRF52832 DK SDK: 17.1 SD:S132_7.2 Sw: ble_uart_c Issue: nRF52832 as a central to scan a peripheal(not nordic chip),the nRF Connect APP can discovery all the service, but...
I am trying to connect RPI(and/or Nvidia Jetson) with nrf9160 custom board(Icarusv2). I am using this custom board for other purposes and it works fine. For now I found only...
Hei,
I need to find the documentation for the NRF SDK 1.8, there's a page which has links to all the documentation versions:
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
I am working with nRF52840 SoC (custom board) and AT25QL641 QSPI Flash chip. I am on v2.1.0 of nRF Connect SDK. The slot1 (update slot) is on an external flash.
...
I am using the serial port of SDK7.1 to send and receive data, and this serial port is a serial port of nRF51_SDK_7.1.0\examples\peripheral\uart\pca10028\arm. Can this serial...
Hi,
I have a project using Zigbee and NRF5340.
I'm facing a "zboss_osif ZBOSS fatal error occurred" from ZBOSS lib after few days of operation.
I'm wondering if the...
Hello,
first I would like to "set the scene".
* hardware : cutsom board
* mcu : nrf52832
* nRF5_SDK : nRF5_SDK_17.0.2_d674dde
* software : mbr + bootloader + softdevice...
Dear Sir/ Madam,
What is the difference between:
> nRF2401P and
>nRF2401P-R ?
Also, code that is written using nRF2401P - would it still work when using nRF2401P...
