Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hello, I am writing an AT command response parser for my custom AT commands. I thought about using nordic's parser utils found in include/modem/at_params.h but I have been...
Hi all !
I'm writing this message because I'm having problems trying to increase the number of devices in PAwR (I use Coded PHY).
I based my development on the SDK 2.8...
hello . i tested the sample for the persistance key it worked with the AES key . But when i tried with the EDDSA key i received that error psa_generate_key failed! (Error...
I have 7 GB large .ppk2 file exported by Power Profiler v4.2.1. I am looking for a glitch in power consumption. Doing this manually by scrolling through the waveform in Power...
HI! I am trying to decrease the memory use of my application that is built for a nrf9160 and noticed that tfm creates a 256kB partition that it only uses around 99kB of. RIght...
nRF54L15 has RRAM with error correction codes (ECC) built in, with autocorrection.
I guess ECC errors could either happen due to a power loss during a write (when reading...
i am working with the nrf7002+nrf5340 ns when i run the excercise solution and press the button a couple of times, i get this error *** Booting nRF Connect SDK v3.5.99-ncs1...
I am bringing up a brand new laptop for devlopment.
I downloaded and installesd nRF Connect, SDK 2.6.0, SDK 2.7.0 and SDK 2.8.0. The SDK 2.9.0 installation failed.
I...
I plan to use an ESB as a low latency and high speed protocol.
However, there must be multiple hosts on one network.
Hosts or devices must be able to communicate with...
Hi,
I have a design which mostly follows the reference designs.
I've added a Resistor Network R16/17/24 to allow a UFL connector to connect to the ANT and isolate...
Hello, I really need some help to connect a central nRF52 DK board to a peripheral that was provided to me. This peripheral can connect to a smartphone using nRF Connect and...
NCS 2.7 with Toolchain 2.7
Launch build from Visual Studio
Sysbuild with mcuboot and custom application, custom board
Although the application itself updates when VERSION...
In our custom board nrf5340-nrf7002, tried system_off(C:\ncs\v2.6.1\zephyr\samples\board\nrf )sample to check power consumption.
But it measures 0.60mA Is there any config...
Hi Nordic DevZone team,
We would like to get nPM Power up for nPM2100 because it seems not to be supported for nPM2100 in nRF Connect.
We are plannning to let the customer...
I've worked with the nRF5 SDK in the past, and I've started exploring the nRF Connect SDK for future projects. I've taken some of the courses offered through Nordic (great...
