Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
I am using the NRF9160 for SPI using an external Flash. After using the 'http_application_update' samples, I was able to get the value of the data written on the external...
Hi, I am a MCU developer searching BLE MCU to develop some IoT project.
I would combine nRF series and LTE NBIoT module for IOT project.
And I need to integrate many different...
Hello all,
I am trying to use my nRF52832 DK for a wireless camera shutter for my phone. I have reviewed the example code from SDK 15.3.0 named ble_app_hids_keyboard as...
Using SES, nrf52840DK, the onboard debugger.
I am able to set a breakpoint and use condition like x == 5.
I am unable to use anything but the == operator. In SES I...
On line 904 of nrf_log_frontend.c there is a log message to indicate the backends are flushed – but this message adds a log to the queue. If auto flush is enabled, this can...
Hi forum,
I am worked on nrf52832 using sdk 15.0.0.
How to used RTS and cts for enable HWFC on nrf52832.
Is their any example for HWFC control through RTS and CTS line...
Hi Devzone,
I use Thingy91. On the nrf9160 side, I run mqtt_simple example; on the nrf52840, I run connectivity_bridge with BLE feature.
When I send "900" via nus service...
I want to control two RGB LED strips with I2S with different GPIO. Not able to figure out how to achieve it. While trying to initialize by separate buffers and data handler...
Hi there,
I have successfully programmed the nrf24le1 on the radio module using the nrf6700 (motherboard) through nrfgo studio. I did so by plugging the radio module into...
Hello,
Is the Power Profiler App capable of calculating and outputting the cumulative energy output to the device under test (when in Source meter mode)? I am using the...
Hi!
There is two things confusing to me about taking IQ samples in AoA application.
1. It is clear to me that that the time between switching of antennae (TSWITCHSPACING...
Hello,
I am using the Nordic SDK v1.5.0, the modem firmware is mfw_nrf9160_1.2.3 and the DK for the nRF9160
In our application, we are using AT commands to setup and control...
Hi,
There is a similar case:
High power consumption in sleep mode after using SAADC
But I am using the SAADC driver version 2.0 because the oversampling feature is only...
I have seen multiple posts about the nrf5340 that confuse me. Posts like this one say that the board/chip is not available yet, as of 4 days ago. But after looking through...
