Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi Folks,
I am currently working on a BLE configuration composed of two NRF52840 chips. One is configured as central and the other as peripheral and use coded phy (long...
While I am going to pair with my android 9 Asus mobile phone with SDK 17 nRF52840. It in my mobile showing "Pairing rejected by Nordic_HRM". After that I have added a some...
Dear community,
I am trying to implement a custom service, however I am struggling because many example codes are for PCA10040, Softdevice S132 and/or for older SDK's. I...
Would it be possible to get the SHA256 hash for version 5.1.0 of the S132 soft device for the nRF52832? Just want to verify the integrity of the download. Thanks.
Hi All,
I am currently designing my PCB using nRF52840 chip.
I was using the footprint downloaded which was in nRF52840 dongle pcb library given by Nordic. During DRC...
Hello,
I am using Nrf51822.
I am using sd_110/application/bootloader, etc. in SDK_10.0 without problem.
Recently, migration to SDK_12.3 / sd_130 is in progress to...
How wide are the peaks? I know that it depends on many factors how high and long the peaks are. Currently we have measured peaks of 450 mA for 40-50 ms in our application...
Hi,
I am trying to run the Zephyr BME280 sensor sample application (using nRF9160 DK) in NCS1.3.1, but get the below error:
My prj.conf is as follows:
And board...
Hi all:
I install "nRF Connect SDK v1.3.0" by Toolchain manager,
but it always show "Failed to clone the repositories".
Could you have any suggestion?
best...
I am trying to interface my nrf51 DK with the Lis3dh sensor . I have one reference code by elmot for the project and it is working.
https://github.com/elmot/nRF51822xxAA...
Hi,
I'm comparing the nRF9160 DK and Thingy 91. The purpose is to copy the LTE RF design for a Band-20 application. The GPS will not be used.
Question: Is the complexity...
I have bought two thingy 91 to develop the tracker using GPS and accelerometer. I did all the step by step to load pre-compiled hex file given on the website. Then I created...
We are making customize the wearable who records the data from the accelerometer and GPS sensors and sends it back to our server. SO, we decided to use thingy 91 chip has...
Hi,
We built the Blinky sample with NRF Connect SDK 1.3.1. It works fine on NRF52833 DK, but when flashing on external custom NRF52833 board the firmware won't start without...
