Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi all,
I've found an alexa gadget example but I can't seem to get it running on my nRF52840-DK. The example I've found was located under repository:
https://github.com...
nrfx_gpiote_irq_handler() which is nearly 150 lines of code. All the GPIOs seems to have same priority at the hardware level, how among different GPIO's Interrupts are processed...
Hi, I got an SDK15.2 project that we converted the bootloader to be both serial and ble for the dfu. Unfortunately we have a few units in the field that have only the BLE...
Hi,
I want to schedule timeslots back-to-back, or as close as possible. Question is how close to eachother timeslots can be scheduled?
I read the following about sd_radio_request...
I have a custom BLE service that works correctly with nRF Connect. When I use the API, though, it sends me the same value repeatedly and does not update to reflect new values...
Hi,
I am a developer of IoT systems working for a private firm within Africa. I currently started the development of a cellular IoT solution and my search landed me on the...
Hi,
I've somehow managed to build the gps sample from source within SES, but I can't get the flashed sample to work properly. Everything is fine if I flash the downloaded...
https://devzone.nordicsemi.com/f/nordic-q-a/46388/nrf9160-dk---make-application-from-scratch
I followed the steps from user: Aakash_Soni on this thread. However, when...
Hello,
I am using Segger Embedded Studio IDE v4.52 (64-bit) to develop an application using nRF5340pdk.
My question is this, I cannot find any of the Preprocessor or compiler...
Hi.
I am developing using nRF52820 with SDK 17.0.0 . I test the USBD using the example code(\nRF5_SDK_17.0.0_9d13099\examples\peripheral\usbd_hid_generic), but the problem...
Hi,
I would like to know if it's possible to read advertising data when connecting to the peripheral.
My problem is sometimes when i read the adv data, and then try to...
Hi,
I try configure 2 gpio pins with opposite pull state, one NRF_GPIO_PIN_PULLUP, other NRF_GPIO_PIN_PULLDOWN :
nrf_drv_gpiote_in_config_t in_config = GPIOTE_CONFIG_IN_SENSE_LOTOHI...
Hello
We are working on BLE remote based on nRF52810. We are operating it through coil cell. Please let us know is there Internal battery monitoring feature supported by...
