I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hello, everybody.
I'm working on combining the nRF52840 and the GPS module and are currently developing a program that stores real-time GPS data in an external flash memory...
Hi,
We are planning on upgrading the firmware on our device from Mesh v0.9.2 to Mesh v3.0.0 via BLE.
Specifically, our current stack uses: - nRF5 SDK for Mesh v0.9.2 ...
IPhoneX sometimes goes into the ble_evt_handler auth_status event, and then p_ble_evt->evt.gap_evt.params. Auth_status.auth_status!= BLE_GAP_SEC_STATUS_SUCCESS, other iPhone...
I am unable to compile any SDK12 example with SES even following the tutorials. Versions in tutorials are different from those actually available resulting that menus shown...
What is the difference between the twi_sensor example and the twi_master_using_app_twi example? Where do I find any documentation that describes the available functions for...
Hi
we are currently designing a device using the nRF52840 and are looking for information on the most cost effective way to do large scale production testing.
will we...
Hi,
I have an issue with pinging the nrf52 (PCA10040)(with mqtt_pub loaded), from the PC on the LAN to which the Raspberry Pi is connected to.
I can ping the nrf52 from...
Hi, I've followed the tutorial on https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial . I got to the end of the tutorial...
Hi,
In your reference design: https://www.nordicsemi.com/DocLib/Content/Product_Spec/nRF52840/latest/ref_circuitry?1070#unique_1780233596
There is a line from DEC2 to...
When I debug my product ,using nrf51822, using the ble_uart example, my product will using MCU commnication with BLE,using uart.
When I modify the PIN of the uart TX pin...
Hello:
I am working with my sales contact at AT&T in the USA. I mentioned this module and that it was going through certification. Before I moved forward with the carrier...
Hi,
I'm using an nRF52840 dongle with pc-ble-driver on Linux. It has connectivity 6.0.0 with S140. I tried the heart rate collector/monitor example pair (I have two dongles...
Hi folks,
We are in the process of evaluating nordic chips for our product.
One of the features we need is the ability to record an audio sound from an Ios app, send it...
Hello,
I have got nrf Power Profiler Kit for power consumption testing in our application board. I have a question regarding its output voltage for DUT devices. My application...
The project I am working on is to store the data acquired through BLE_uart_c and the data collected by the sensor on SDCard. I use FreeRTOS. The problem is described as follows...
