Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Hi all,
I've just started working with the nRF24L01+, and I've come across some issues when attempting to do an initial read from the datapipe 0 RX address.
After reset...
I am in the startup phase of a uni-project and I would like to ask you about the feasibility of using the nrf24L01p with power amplifier as the radio module. Specifications...
Dear all, I'm trying compile github ble example ble_app_hello_world for Nordic nRF51422 following steps on Tutorial Advertising for Beginners and found 6 errors all same type...
Hello,
I am using enhanced shock burst as communication protocol. Currently i am using rtc 300us timer to call nrf_esb_add_packet_to_tx_fifo() to transmit data every 300...
I have a custom board with the nRF51822 chip, the chip is set-up with the recommended (CFAC WLCSP schematic with low voltage mode) setup, excluding the external low frequency...
Hi,
I just finish designing my board and soldering it using the Bluetooth low energy nRF51822 chip and i want to test it.
i want to know if i put the coin cell 3v and...
Is the ECDH encrypted key exchange supported on the new S130? If not, when can we expect it to be available?
I am surprised this is not given a higher priority, since now...
I use s110 v7.1.0 ,nrf51822qfaa.
now I find the pstorage_store work is OK if I is not run sd_ble_gap_adv_start function.
but I fin the pstorage_store work is wrong if...
I use s110 v7.1.0, nrf51822qfaa.
The write flash data using pstorage is OK ,before ble_advertising_start() function is start run.
But if I run the ble_advertising_start...
Hello,
I am using the nrf52pdk and am wondering if there is a way to force an output compare interrupt to occur. For example, lets say you want to generate an interrupt...
Hi,
on the nrfprog you can detect all connected Segger programmers.
If I have 10 Segger Programmers connected, I can address each of them with the nrfprog to programm...
Hi,
I am new to Nordic. Will someone help me figure out what is wrong with UVision V5.16a. I get sample codes from pack installer example the "ble_app_hrs_s310_pca10028...
I've followed the instructions here to try and get my J-Link debugger to run in bootloader.
I am using a newer SDK and SD (than the post was written for) so that may have...
Hi !
I have a rather strange problem: 1 packet is transmitted for 30 milliseconds.
I use iPhone-4s with iOS8.1 and custom board with nRF51822
In the firmware exists 4...
