The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
Hi
I got some questions about the RF part of the ref schematic.
1, why the bias voltage for ANT1 anf ANT2 are not the same since they are differential lines?
2, what...
Hi,
Today I use the app timer to start a simple 8bit ADC conversion each second and send in the irq handler.
Now I am trying to use the sw interrupt to execute some...
Hi
I want a 1K Hz square waveform to drive a peripheral device, but I can not get a continuously square waveform on GPIO 19, pls have a look at the picture I attached,...
Hi All
I am facing one issue using app_timer.c, When I put the PRESCALER value as 327 and started timer as app_timer_start(timer_ID, 100, NULL);, It was giving only 920ms...
Hi,
I ran the Nordic nrftoolbox on Sony Z1 android 4.3. I found that the device name is not showing on the list as attached. Running the Nordic nrftoolbox on Samsung S4...
Hi there,
We are using the nrf8001 and a arduino to read out two sensors.
The two measurements should be at the same time and therefore are coupled to eachother.
Is there...
Hi
I try to program my custom board using J-flash and Flasher ARM ( for production ).
Attached my J-flash configuration.
Connection with device is successful established...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I tried the booloader program on nrfgo mother board and it works as it is.
However, after I followed the same procedure and download to our inhouse board which is...
Hi!
I'm trying to receive notification on a characteristic that I've written before but I can't. I've activated the Notification in that characteristic, after that I write...
This question is somewhat related to: devzone.nordicsemi.com/.../how-to-switch-between-over-the-air-and-uart-bootloader-mode
I know it is possible to switch between HCI...
Hi
I'm working on the DFU feature according to the "device_firmware_updates" example on PCA1001 board, basically it works, but the question I'm facing is the board always...
hello,
We used the nRF51822-BK-FW 1.0.1
We need a little more help here to add the MAC address to the advertising packet. Can Any one help us add that to there?
i m attaching...
Hi,
Could anyone give some idea how to do data transfer with help of L2CAP (calling L2CAP APIs from Application)? I will be very much thankful if give description/steps in...
