Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I cannot get the nrf5340 audio dk kit to work from USB input properly. After a reset, it only works for a fraction of a second and audio stops. Has anyone run into a similar...
Dear:
Production input 1300PCS, DPD current poor 64PCS, defective rate of 4.9%
Conclusion: Through verification, it is confirmed that the DPD current caused by U1 chip...
Hello,
I'm using nrf52840 together with HX711 24bit ADC . My application samples the ADC every 12.5ms (80Hz rate) and the sample is sent out via BLE notification. The HX711...
We have an issue with initializing our i2s instance as mentioned in sample code with an `id` of `0`:
We get this error:
To fix we reverted back to the 2.6...
We're having an issue where our nrf52840 appears to stop advertising, and isn't able to resume advertising.
Our device is a custom PCB based on the Thingy91 (has both an...
Hi guys , another question here regarding Cmock and opaque types . I am currently trying to mock a function with an argument that contains the type "struct bt _conn " . However...
Hi,
I am developing a nrf5340 based device (no external memory) using FOTA to update the firmware. This process used to work quite well for a while now, but I ran into trouble...
We're using a noinit section of ram to store a "reboot reason" if/when we need to do a SW reset (i.e. in a watchdog handler).
This works as expected, we set the reboot reason...
https://github.com/zephyrproject-rtos/zephyr/blob/main/samples/drivers/spi_flash/src/main.c#L36 may I know where I can find the pin connections used in this example
"const...
Hi.
I have following error:
Here is my prj.conf :
I would like to avoid using CONFIG_SHARED_INTERRUPTS.
Only GPIOTE0 is on IRQ number 11 so I couldn...
Hello ! I'm trying to adapt the code from the master-slave SPI example ( https://github.com/too1/ncs-spi-master-slave-example ) for my nRF54L15 development kit.
The master...
We are using modem firmware 1.3.5 on nRF9160.
When packet loss is high, we sometimes see connection resets (NRF_ECONNRESET) reported by the modem that don't seem to be explainable...
Hi,
I try to use CPSMS command to reduce the power consumption. The idea is to send a MQTT message every 10min and have the GPS coordinate every 5 min.
The NRF9160 is...