Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
Hi,
I am working on nrf5340. I would like to change the TX and RX default pin of uart0 to <33> and <32>, I modified the file "nrf5340_cpuapp_common.dts" as below.
The...
I've been develop the other MCU;s DFU driver for the nrf52832 recently, and I ran into several problems.
The first I show you my DFU step in the RTL8720( Be the central...
Hi there!
I'm using the nRF Connect SDK with the VScode extension for developing an application for the nRF9160DK. I've taken the lwm2m_client sample as base and rewrote...
I'm struggling to get buttonless DFU to work with FreeRTOS. I've gotten buttonless DFU sample to run on the hardware. I also have FreeRTOS running on the hardware. However...
Hi team,
Environment :
nrf52840
s140
1.How to enable the second regulator stage REG1 use of DC-DC converter ?
2.What is the default configuration HFCLK and how to...
Hi Everyone,
Wanted to test the NFC library provided by the nrfxlib on the nrf5340DK. Added the following config file:
Resulted in:
How could I check the reason...
Hi,
I have added a nrf-9160 DK device to nrf cloud and it is always is shown as disconnected (disconnect reason MQTT_KEEP_ALINE_TIMEOUT ).
Previously i have updated the...
Hi
We are using a nrf52840 on a custom board.
The board always worked fine.
Flashing is done with :
- SEGGER J-Link EFM32GG-STK3700
- nrfjprog version: 10.15.0...
I am seeing the error below when I try to launch a debug session inside the IAR IDE.
I am working on the nRF52840DK and am seeing this error on the DFU example in the...
I'm Using sim card which support both LTE and NB-IoT. In some areas i can't use LTE-M and in that case i need to switch it to NB-IoT. I referred and there is fallback method...
I am using the Ceedling framework for unit testing my firmware. This has qorked quite well. But now I wanted to use the section variables to decouple my code a bit more. And...
Hi. I would like to know how to do a DFU over UART using a custom desktop application (without using nrfutil command nor nRF Connect app). What would be the UART protocol...
Hello,
I have the same problem as this topic: https://devzone.nordicsemi.com/f/nordic-q-a/77267/nrf9160-azure-iot-hub-on-thingy91-mqtt-connect-error
I'm using nrf Connect...
Hi,
We are trying to use our NRF91-DK with a proximus simcard (belgian provider). I'm trying to get the https-client example to work without any code modifications. We know...
Hello,
[this question is related to this other question ]
I am using the nRF9160 SoC, the modem has firmware version 1.3.0 and the Nordic SDK is v1.5.0.
My goal is to...
