Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Hi, Hope your are well, i am currently in the final part of my project where i am SPI Gyroscope float data from one nordic nrf52dk (S132) to another such that i can analyize...
I am running read str 0x3e000 12 via UART line but there is nothing which gets printed on the terminal.
Even if i write some hex value to a particular flash memory location...
Hi there,
I have set up the nRF2427 with the nRFgo Starter Kit motherboard (nRF6700). The motherboard is recognized and I have all of the 2.4GHz options available. I would...
Hello,
I am working on the nrf52832 board with SDK16.
I am using a custom BLE example.
My TWI and BLE code work ok individually but when I integrate them it does not...
Using S132 v7.2, I'm getting a hard fault at PC 0x00015810 (I see the flag set in SEGGER, and the console outputs a SOFTDEVICE ASSERT FAILED error) that I'm working on manually...
Hi,
The 'nRF Connect' SDK (v1.4.99-dev1) sample OpenThread CLI is programmed to receive 'ot' commands from UART console. When configured with multi-protocol support, the...
Hello,
I have a problem that sometimes the supl_client_session() function halts the system by not finishing and ending the session while getting the timeout expired SUPL...
Hi
I can't find fwid for sd132 7.2
|s132_nrf52_5.0.0|0x9D| |s132_nrf52_5.1.0|0xA5| |s132_nrf52_6.0.0|0xA8| |s132_nrf52_6.1.0|0xAF| |s132_nrf52_6.1.1|0xB7| |s132_nrf52_7...
Hi there,
Our team is developing an application based on the nRF5340-DK - we are developing on the DK while our hardware is in transit. Our schematic largely follows the...
Hello, I use the internal crystal, the application in my board runs normally and it shows the board is in fast advertising state. However, I can't find bluetooth signal through...
I'm running the Zephyr hci_usb sample on a nRF52833DK to see if I can use it as a Bluetooth dongle on my Ubuntu dev machine. It appears as /dev/ttyACM0, so:
sudo btmon ...
Dear Nordic,
I have a BLE mesh product that is in pre-production. The mesh gateway is composed of an nRF9160 and nRF52840 with a UART link connecting them. The nRF52840...
Hi,
I have updated nRF Mesh to 3.1.0 version (iOS), but I can not see any field for reading sensor values. I set app key and publish/subscribe addresses for sensor server...
Disclosure. I am new to firmware develoment. My experience is in cloud development.
I just bought a Thingy91. I registered online using nRF Cloud. The modem communicates...
I want to use a timer to get a fixed time interval, so I use a 32-bit timer to count from 0 to 10000, and use PPI to clear the counter when it is captured to 10000, such as...
