I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Is it possible to use the J-link to debug a stand-alone PCA10004 ? I am not using the motherboard. Powering the board separately. When I try and run debug in Keil I get error...
I would like to ask a question about the time of :"Time between DISABLE task and DISABLED event when
the radio was in TX" of the "Jitter". In the picture show the "Jitter...
Dear nordic guy, I'm developing
with nrf51822. I have one question regarding main clock control.
I want to turn on and off 16Mhz clock in application side.
application...
Hello,
I have some code running that transfers binary data from an iPhone to a nRF51822 device (used for firmware upgrade).
I have used a variable length characteristic...
When starting with nRFgo Studio "Erase all", "Program SoftDevice" & "Program Bootloader" to have a almost virgin base without an application, I succeed perform an over the...
Hello,
currently I am thinking about the proximity concept. The following scenario is given:
We have a Display that shoud lock/unlock a Device
We have a iPhone...
I used SDK 5.1 and S110 6.0, I dowmload the project ble_app_ancs to nRF51822 DK. I try to connect it to iPhone 4s (which run on IOS 7.04), when I click 'pairing', the led...
Device: NRF51822; BMA250E
Description:
When I read BMA250E via I2C without BLE protocol, commnucation run well.
And if there is no I2C commnucation, BLE protocol can...
Hi all,
My questions are related to frequency on the soft-device firmwares for nrf51822.
In S110 does the frequency channel hop according to the CONNECT_REQ packet...
Hello,
I am testing the ble_app_hrs project on two eval boards, with s110 and s120. Everything works.
If I power-off the peripheral board (s110), it seems that the master...
Dear Nordic guy, I'm developing with nrf51822.
I have one question regarding flash write.
In ble connected state,I have some error to write some data to flash.
I want to...
Hi,
I just loaded the nRF8001 Arduino code on my board and used an iPhone 5 to read the data that was being advertised. I get the following response:
<CBCentralManager...
Dear Nordic guy,I'm developing with nrf51822.
I have one question regarding lfclk.
I use LFCLK SOURCE RC OSCILATOR of ble_stack_handler_init() at the application side.
...
