Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I'm like 99% certain this isn't possible but has anyone tried running VS Code Server with the nRF Connect SDK?
https://code.visualstudio.com/docs/remote/vscode-server Compiling...
Hi,
1.Mode B prevents RF9160 from entering low power consumption. How to disconnect RTT from nRF9160 module in mode B
2. In normal mode A, disconnect RTT from the computer...
Hello, I implemented the function to receive an external 62.5KHz clock as an interrupt and repeat the process at a very regular time using PPI. However, sometimes PPI processing...
Hi,
I'm using SDK 17.1.0 on nRF52833 DK.
Now I want to transmit some data from mobile app to DK board by using examples\ble_peripheral\ble_app_uart.
NOTE: ble_nus_data_send...
Hello Nordic Team,
I have a question regarding usage of RTC. My application is based on nrf52840 and uses BLE + Zigbee + FreeRTOS. From this page: https://infocenter.nordicsemi...
1.I am testing the NRF5340 Audio and fully following the
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/applications/nrf5340_audio/README.html#fota-build...
Hi,
I tried to use the sensors on the Thingy:53.
However, it looks like the BMI270 on the Thingy:53 is not supported by the nRF Connect SDK because the SDK only supports...
Hello everyone:
I'm following the tutorial in JWT authentication on nRF Cloud | nRF Cloud Docs .
And I want to test the REST APIs by using curl command.
I have created...
Hi,
I think this is a regression or related to this issue:
Attached is a very simple example with the [email protected] - if you build it with `CONFIG_DEBUG=n`, it...
Hi all! I am working in a BLE scanner but I have enabled the filter by MAC ADDRESS. I can filter beacons that are produced based in NRF52 and NRF51. But when i try set a MAC...
Hello,
I am running into difficulties getting the sleep current below 2.356mA. I have a custom board but I went ahead and tested it sleep current capabilities by programming...
Hello,
My application (nRF52832, SDK17.1) uses the fsotrage library for low-level sequential data storage and retrieval.
At the moment I'm using nrf_fstorage_sd as an...
Hi,
I am using nrf sdk for mesh v5.0.0 and we are building our application on top of sensor_server example. I am provisioning the nrf52832(which is acting as sensor server...
Hi Team Nordic,
For setting up a thread network using nRF5340 DK's, I wanted to build and flash Thread: CLI sample from nrf repository. I use nRF Connect for VS Code with...
