Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
Hi,
I am currently working on a project similar to this thread:
However, the thread stop updating. I followed what Einar suggested, to merge the Decawave example code...
Hi all,
I have an issue on my device. We have implement OTA update but sometimes, the nfr stucks on DFU mode after the update. Even if the update is succesfull.
We use...
Hi All.
I am checking battery autonomy with different settings in my Module (with an nRF52840 SoC inside) since, in my project, this is a critical restraint. I am feeding...
now, I need transfer data between nrf52840 (base on zephyr OS) and python app through PYSERIAL. Is it possible to use something like RTT or shell_uart to transmit/receive...
How do I switch between being SPIS/SPIM with the Zephyr library?
I am using ncs v1.9.1. I have code that works separately as a slave or master but I need to make it dynamic...
I want to use +8 dBm TX power so I added CONFIG_BT_CTLR_TX_PWR_PLUS_8 to my prj.conf, and then realised it doesn't do anything.
I then found set_tx_power() on these pages...
The problem: We are getting a hard fault immediately after jumping from the bootloader while trying to initialize the nRF USBD driver. The fault happens in nrfx_power_init...
Hi,
We are trying to integrate a remote controller functionality for smart TV and set-top box etc, using our product based on nRF52832(nRF5 SDK). I understand that we can...
I am trying to use a SPI bus with three MAX3109 chips attached to give me 6 UARTS. My overlay is defined as follows:
& spi1 {
cs-gpios = <& gpio1 13 GPIO_ACTIVE_LOW...
Hello, I'm working on a s332 application and I need to include the DFU feature in the code. I've managed to perform a DFU on s132 applications following examples like this...
I've built and able to the run the 802.15.4 RF Phy Tester but it doesn't seen to recognize any of the custom commands. Can you provide more insight into this please?
Please ignore Product Type I selected - i set it to just select that to something.
I'm planning/designing a comm box, which needs to speak to ZigBee based nodes/sensors...
Hello
I'm a beginner. I am using NRF52 series and coding in segger embedded studio. I have modified the ble_uart example and added some extra code so that I get the sensors...
Hi,
My customer occur a problem with nRF5 SDK10.0.0, the sample ble_app_hids_keyboard.
We test the sample on nRF51DK.
We connect the DK with an Android phone, and bonded...
