I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hello
I'm using NCS 3.1.0 and I’m able to use signed files for FOTA. However, I would now like to add encryption, but I can’t figure out what’s not working :
app/ ├──...
We are preparing a product for production and have enabled authenticated debug access on the NRF52840. Because authenticated debug access is not described in any Nordic documentation...
Hi, I've installed Visual Studio 1.90.2 + nRF Connect for VS Code Extension Pack v2023.11.3 + v2.6.1 toolchains + v2.7.0-rc2 SDK. Then I create a new application, copy a sample...
Hi,
I'm having a problem with sending notify packets, I'll describe the situation I'm doing.
Problem :
I have 5 devices connected to the board and I want to send a first...
Currently on NCS 2.9.2 and radio_test is buildable with CONFIG_BT=y and CONFIG_COUNTER=y. Trying to switch to 3.1.0 but getting an error that "MPSL reserves TIMER10 on this...
Hi There
I run a NRF52840 with the MESH SDK, and use the Flash manager provided.
After some time i would like to update the Device over FOTA this ends in a Assert on booting...
This is my basic information:
1. SDK version: V2.8.0
2. Project: Matter Light Bulb
3. Board: 52840DK
This is my question:
I can use this command to commission bulb...
Hello all. I have an issue in production of a device that utilizes the 52833, aQFN73 7x7mm package, in regards to the pad stack dimensions. I wanted to check the datasheet...
I work currently working on a driver module supporting your nRF91x1. I schedule rx-operations via your nrf_modem_dect_phy_rx() dect_phy modem-api. I am using the .handle field...
Hi Nordic Support Team,
I’m working on an application running on a custom nRF5340 board with nRF Connect SDK 3.0.2.
My goal is to perform BLE DFU only on the Application...
SDK17.1
MCU: nRF52832
My product supports connecting to two master devices. After successfully pairing and bonding with both master devices.
Is it possible with the...
How does VS Code know which nRF5_SDK_xx to use?
Where does VS Code get the nRF5_SDK_xx files to build the BLE app?
PS. Using VS Code V: 1.104.0
Any help appreciated
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
my nPM2100-EK can no longer connect to the PowerUP app.... all was working fine for the first few days, but no nothing.... the problem is the same on my PC and Mac....
when...
Hi Team,
I'm encountering an issue when using scan and STA mode.
When I run the shell example along with my custom board, the scan works successfully the first time. However...
