It would be very helpful to hear of others experiences getting these licenses, also I would like to find out if anyone has any advice of anything to be included or excluded...
I wanna implement this code for the app inventor, but there was several problem here. I can't use array or index for developing my trapezoidal method.. like this..
code...
Hello,
We are looking for a developer a single task project. We need to provide all of our developers with the same development environment, so we are looking for someone...
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am a beginner at Nordic. I want to understand how I can access a pin named " P1.04 ...
Hi,
I faced the exact problem nda , here . I take step just like nda did before. I unchecked "Enable debug options" as Marte Myrvold told, but still the same problem.
...
I am working with nRF connect SDK with nRF52840 dongle. I am compiling code using nRF coonect for VS code with nrf52840dongle_nrf52840 board.
For Programming nRF52840 dongle...
Hi
I have similar question to the post https://devzone.nordicsemi.com/f/nordic-q-a/7013/nrf51822-internal-ldo-output-pin .
I need a stable voltage to elevate the reference...
Hello everyone,
I use the multirole software as base for my application and I programmed everything with a evaluation board. I design my own PCB and decided to not use the...
Hi,
Is there any sample in nRF_Connect_SDK that implements RTC on nrf52840 SoC?
I need to implement RTC in my application, so is there any example reference for this...
Hello,
I am trying to set the `BT_SHELL_NUS` project up as a standalone repository. My requirements for this are as follows: I only want to commit application code to git...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We had to change the SDK version to 1.9.1 from...
I am trying to implement RSA signing into my application, I am planning to use the following example as a starting point but the sample, with no modification appears to not...
Hi there,
We are developing on the NRF5340, and have a question regarding the drive strength that can be set on a GPIO pin using the PIN_CNF register.
However we can not...
Hello,
i am using the nrf52810, ble_app_template example to read Accelerometer and gyro-meter data from ICM42605 sensor. so i have followed the i2c communication tutorial...
Hi there,
We are not able to find the reset due to brownout within the RESET->RESETREAS register? Is this the case? There are explanations of the brownout detection in the...
I'm trying to get DFU working with LPN on the 833. The sequence I follow is: (Erase board) Flash Soft Device Flash Bootloader (Using mesh, but don't want serial)
Flash Device...
Hi,
I'm trying to setup a very basic network based on the thread CLI example.
I have an nrf52840-dk as a router/commissioner and a custom device as a nrf52840 joiner...
This is the next step of the process getting the canbus working with nrf9160 and the aditional MKR CAN shield from arduino
previus part can be read here https://devzone...
