Hello,
We are looking for a developer a single task project. We need to provide all of our developers with the same development environment, so we are looking for someone...
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi!
I want to use my nRF 52840DK as a general purpose BLE demonstrator. I know that this is already possible by using nRF Connect for Desktop, but I'd like to develop a...
Hello,
according my Observation Zephyr, more precisely the rpmsg stuff for BLE between both nRF5340 cores, doesn't work when optimization is switched off. But stepping through...
hello Nordic
i am working with nrf52840 with ncs (on the process of moving to 1.8 currently 'v2.6.99-ncs1-1' )
i have several sensor drivers on my board and flash driver...
hello,
i am using nrf52832 with lis3dh accelarometer and max30205 temperature sensor in our customised board with sdk 15.2 i have included the dfu ota in my firmware my...
hello nordic team I ran the ble_app_uart example in sdk 15.3.0 on nrf52832. When i add printf("\r\n%d\r\n",15); to the code as follows, the program prints 15 to the serial...
Hello.
We are developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
I am creating a process to set the characteristic and send an indication using sd_ble_gatts_hvx...
Thank you very much for your help. I am currently working on implementing a PWM control function using the nrf52840. I would like to ask you about a build error that occurred...
I need to know in which case the SIW_DET pin is used. Does it depend on the version of the nRF9160 ? Then which versions ?
And is this detection function better in software...
Hello, guys!
I am using nRF51822 SoC with Zephyr. There is a need to configure multiple GPIOs as inputs, with the possibility to fire an interrupt on rising/falling/both...
Hi There,
I am working on a project based on nrf51822. I need to establish pairing the device with smart phone by clicking a button as confirmation on the nrf51822.
...
Hello,
I already fully understand how nRF5340: Network core bootloader working.
As I wondered in the title, I want to move the application firmware data of network core...
The project uses nRF5340. A signal is connected to P0.27/AIN6, and during "normal" mode the pin is used as an ADC.
Before going into sleep mode we would need this pin to...
Hello,
I am working on a project which is based on nrf52840 and Zephyr.
Current prototype uses Adafruit nrf52840 sense board with spi based display attached.
I am new...
Hi,
I experience a very strange issue with UART.
When I try to send data via /dev/ttyACM0 device it looks like the characters sent are buffered and sent only upon the...
Hi! I am in the process of trying to install the Asset Tracker on my Thingy91. I have got it to work with nrfCloud and I am now trying to configure it to use the AWS backend...
