Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
I'm trying to use the SAADC to return one value so I initialize it, try to take the reading, then unitize it so I can use it for taking readings through the PPI. The SAADC...
By default, is it enabling or disabling bias correction? If no, how to enable bias correction?
Is the RNG peripheral being left on all the time as a result of us using it...
hello,
I need send 10000bytes large data send central to peripheral in single transmission. I using example code ble_app_uart_c in SDK15.2 nrf52832. what are the parameter...
Hello
I am writing low-power application where NRF is called from the other chip by interrupt, performs bluetooth scan and sends data back over UART. Of course, I want to...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image.
I am using ‘ble_app_bliky” for my application development. In this “Button...
Hello =)
Im trying to run the ble_app_uart_c example on a NRF 52810 Chip.
i got:
SEGGER Embedded Studio for ARM V4.12
SDK 15.3.0
examples\ble_central\ble_app_uart_c...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image.
In ‘System OFF’ after GPIO interrupt, chip will reset and control will come...
Hi All
I am using nRF52832 with softdevice s132_nrf52.6.1.0
and I have to use both protocol (ble & gzll)
the default protocol is ble
after i keep pressing the button...
Hello,
I am working with nrf51822. I have developed a custom evaluation board. Accidently I connected voltage in reverse polarity to the device now i am unable to program...
Hi,
I am trying to understand possibilities provıded by Bluetooth Mesh Technology.
In my topology, there are tywo types node.
The first type of node is connected to...
Hii,
I am currently using two nRF52832 SDK boards to implement text message exchange with another nRF52832 SDK board via BLE Mesh SDK 2.0.1.
However, when I try to increase...
Hi. I'm using a nRF52840 chip and have a flavour of Proximity profile example being used with some custom services and characteristics that have been added. All is good in...
There is my function for writing to flash.
It works when NRF52832 start from reset, if works when the NRF52832 gets data over BLE but it does not works after "power down...
Hello, for some reason, the UUID's on a Galaxy Note 3 are messed up or are not being read properly. I have included screenshots of the issue. The note 3 is running android...
I'm trying to understand how the UARTs are configured on the nRF9160 DK.
The spec mentions that there are two UARTs, a primary and a secondary. https://infocenter.nordicsemi...
