I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
The 'Debug Out' on nRF52832 (and 52840?) Dev Kits only works at 3V - so won't work with a 1.8V target.
The question has been asked before, and the obvious answer given ...
hi,...
i am using nrf52382 and nrf52840 ... one is client and server . i am using mesh sdk 3.1 .... i have debugged the example light switch server and client respectively...
Hey
This is sumanth. I have worked on mesh beaconing example and saw the output of continuous scanning advertisement of nearby devices in RTT, I made changes in light_switch_server...
I need to configure 1 device as relay node in order to relay messages from the client node to the server node. To test that the sever is relaying messages i could lower the...
Hello and thanks for your help,
We are looking forward to build a low cost and power wireless application using 802.15.4. We do not need any other protocols.
Am i right...
We have an NRF52 set up as Central, connecting to a peripheral (not our own) that's sending notifications with Data>20 bytes
I'm trying to differentiate between it sending...
Hello everyone,
I'm trying to set up entirely open source project for my NRF51822 chip. Everything works fine so far but something strange happens during debugging.
I...
Hello support team,
I am using your product through a module vendor and I have a question regarding errata 197. If the DC/DC regulator only has problems in low power states...
hi... i am using nrf52840 and nrf52832..... mesh sdk 3.1 latest version ....
in this case i am using client as nrf540 and server as nr52832 .... i have debugged the light...
Hello, We planned use nRF52840 in our project, and I have some questions about this MCU. 1) Is it possible to process signal from 8-GPIO with frequency of request 32MHz? We...
Dear,
I am testing nRF9160 DK with iBasic SIM, FW: SecureBoot and AT Client
I am trying to send SMS to my phone. I see : https://devzone.nordicsemi.com/f/nordic-q-a...
Dear Sir,
I am working with
SDK --- nRF5_SDK_15.0.0_a53641a
softdevice -- s132
nrf52832.
I was working with example codes in the SDK folder.
I am working...
Hi,
I need some help calibrating my moisture sensor analog readings using 3.3V regulated power source (VDD = 3.3). Here is my set up, borrowed from the proximity example...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
I am working on an nRF52832 BLE peripheral prototype which sends bulk data to a central as bursts of large notifications. I am encountering an error where the connection gets...
