Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi, I have been looking at the following document nRF9160_OPS_v0.7.1-1510217.pdf which I had downloaded from the Nordic website today. In particular the layout guidelines...
Hi,
I run the "ble_app_uart" from sample program and leave it as it is. The program ends in NRF_BREAKPOINT_COND with "Fatal error" after a while. It is displayed as a screen...
Hello
I am using the nRF52832 with SDK 14.2, JLinkRTT Client, and SEGGER IDE. The system simultaneously runs a soft DAC, IMU, digital potentiometer, and provides variable...
Hi all!
I want to use the BLE stack by Nordic. I figured out that S132 is the appropriate HEX image for nRF52832. I can burn the softdevice into flash with nrjftool.
An...
We have an application where certain executions hold more priority over BLE link. We are implementing a critical section(disable/enable interrupts). However, in some corner...
Hello I've noted some problems when try to use the app_timer in repeat mode with a tick time <= 100ms. I see that the BLE Mesh SDK sets the RTC1.CC[0] compare register in...
I my application, I wish to send a large (60 bytes) bulk of data atomically, i.e. either send all or nothing. Assume I cannot increase the MTU.
Is it possible to query...
Hi
I am using the SDK 15.2.0 and developing for a NRF52832 using Segger.
I have a problem with the define NRF_SAADC_CHANNEL_COUNT in "nrf_saadc.h". It is set to 8. ...
Based on Mesh SDK 2.1.1.
I use light switch proxy client & proxy server to test server publish function.
But when I use the phone setting network, I found that the client...
Dear nordic,
we build a custom board with nrf52840. Now i face some issue i can't flash the board. when i start flashing its show some warning reset pin is high.
I...
Hi,
I just want to verify-
The MAC address of the bootloader is the app MAC address +1, assuming we are using the default configuration.
Is that correct?
Thanks, ...
Hi Support team,
The Online Power Profiler is calculating the Average Current consumption for nRF52840 DK board in a wrong way.
Calculation is of blocks. => Pre-processing...
Hello
I would like to integrate DFU into my application
but, when including:
#ifdef BLE_DFU_APP_SUPPORT #include "ble_dfu.h" #include "dfu_app_handler.h" #endif...
