hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hello Everyone,
I am new to keil and nrf51822 programming.
Currently I am using softdevice s130 with hex file for bootloader from
folder : nRF5_SDK_11.0.0_89a8197\examples...
Hello,
I would like to instruct my application to read the battery voltage on my nRF52pca1040 DK, I am intending to do so through the SADC.
I will feed the board with...
Hi,I have some problems in debug with experimental_ble_app_buttomless_dfu project.
First i build the experimental_ble_app_buttomless_dfu project,so i get the app_buttomless...
We am improvising nrf blinky application, we have got stuck in a problem, after button is pressed from nrf52-dk code goes into forever loop and after a while connection is...
I have two nrf51822 modules and first one is sdk8.0.0 / s110 / peripheral device, second one is sdk10.0.0 / s130 / central device. I've sent a 10-character data array like...
Using:
SDK14
Softdevice132 V5.00
app_uart driver with legacy, no easy dma.
UART is set up with hardware flow control.
The pins should be set up correctly: rx-tx , cts...
i want to konw ble evt struct 's content of meannig . i want to find what's the return value when packet send fail and what is the channel id different from other ruturn value...
Hello,
I want to falsh nrf51422 device. I ma developing software using Eclipse and SDK_7.2.0.
The soft device is 130. I have build the project successfully and Hex/elf...
Hi
I'm trying to communicate between nrf51-DK and arduino using twi. I was able to send data from nrf51-DK to arduino using nrf_drv_twi_tx but when I'm trying to send the...
Reference PWM_driver sample code,
I set the customer status of the LED,
And it also can change status by button,
static void bsp_evt_handler(bsp_event_t evt)
{
void...
Hi,
I want sample code for configuring baud rate of UART from mobile application (nRF Connect). So I don't need to hard-code the baud rate in my program.
Please share...
With version v2.0 of S332, I checked for a return of BLE_ERROR_NO_TX_PACKET when using the ble_nus_string_send function. I use this test in a routine which writes buffers...
I called these command:
nrfjprog -f NRF52 --eraseuicr
nrfjprog -f NRF52 --program app.hex --sectorerase
During the eraseuicr I see:
Erasing UICR flash area.
Applying...
Hi there,
for my Application, I want to listen for all BLE packets on a fixed channel.
No SoftDevice is used.
I receive all packets as long as BASE0/1 and PREFIX0/1 and...
now, i have a question: i have a buffer 100byte data to send, when i send data package via sd_ble_hvx() continus,delay 20ms after each send ,but it will lost some data , i...
