Hello,
We are looking for a developer a single task project. We need to provide all of our developers with the same development environment, so we are looking for someone...
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hello Nordic Team,
I am using my custom board, which uses nrf52840 qfaa chip. I am working with nRF Connect SDK v2.8.0
When I worked with blinky project on nrf52840DK...
Hi,
piggying-back on BT nus shell sample (workspace project), I try to define my own dt nodes.
I keep getting error like devicetree error: /aliases: undefined node...
Hi ALL,
v2.8.0,NRF54L15DK,I would like to ask：
1. if my pin is P0.00, is nrf_gpio_pin_set(0) correct？
2. If my pin is P1.01, is nrf_gpio_pin_set( 33 ) correct？
Hi,
I would like to flash the ad sample on Nrf54L15-PDK
Flash ends with error messages:
build messages:
I'm I tried running west flash --recover.But it didn...
I have completed a mouse program with 52840, but there are some problems at the moment. On some computers, usb will fail to obtain the descriptor, but there is no problem...
One last issue to crack. This one has been in production for a while and hasn't caused any issues other than a little annoyance to the customer. By my measurement when RTC...
Hello,
In regards to the nRF Connect SDK...
I am looking into the possibility of switching out the current implementation of AES used by the Bluetooth firmware. I am curious...
the pin for XL0 and XL1 is P00 and P01
but in my project, I need P00 and P01 works as UART.
I set the parameter to start inner RC clock.and find that: LFCLKSTAT show the...
my costom board is based upon the BT840F fanstell board. I know that this board is based on the nrf52840 QIAA SOC. but I also understand that nrf52840 QIAA has different configurations...
I am working on custom hardware with an nRF52840. I have added the MCU boot in my earlier development as well but this issue I have never faced before.
Problem statement...
Hi,
iam trying to write the data in nvs which i give input through GATT.i can read and write in nvs when not using gatt,BT.
I have 2 codes,1 is working but without GATT...
Hello,
Board: custom board
Soc: nRF52840
SDK: nRF Connect SDK v2.8.0
I would like to know device mac address and use the mac address in advertsing.
can you please...
This page (v2.8.0) https://docs.nordicsemi.com/bundle/ncs-2.8.0/page/nrf/app_dev/device_guides/fem/fem_nrf21540_gpio_spi.html
Suggests copying the following into devicetree...
I am trying to get std::vector to work on nRF52840 running Zephyr in Visual Studio Code running v2.7.0 toolchain , but have been unable to do so. I found some similar tickets...
Hi nordic
I've try to enable 115200 baud UART on p0.9 and p.10 but I can't make it.
I just saw a thread about 52840 can't use 115200 uart at p0.9, p.10:
https://devzone...
