Hello,
We are looking for a developer a single task project. We need to provide all of our developers with the same development environment, so we are looking for someone...
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi, our design makes use of nRF52840 MCU. Power is supplied to VDDH pin from a Li-Po battery which can range from 2.5V to 4.2V. Internal REG0 is used to regulate voltage down...
Hello I want to add an extra config file based on the option in prj.conf or in Kconfg. For example: CONFIG_WIFI_SCAN_ONLY=y include the overlay-nrf7000-wifi-scan-only.conf...
Hello,
When I upload the Matter Weather Station application to my Nordic Thingy:53, I encounter a problem.
I am trying to use Google Home to read sensor data, such as...
Hello, I have a custom development board using the 52840 chip, with two LEDs and a serial port connected. It worked well when developing with nrf5 previously. Recently, when...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
While compiling the custom project in nrf vs code , I am getting the following error;
Configuring incomplete...
Hi,
1. As shown in the following figure, how to resolve such a default instance compilation error?
2. I have used west update to confirm that ncs v2.9.0-rc1 is successful...
Hi,
I have a nRF24L01+ as the TX and have lots of existing nRF24L01+ RXs. I would like use the nRF52810 as the RX as it saves the need for an MCU and on BOM parts. The current...
The text for the recommended nRF Connect SDK workflow (using a Workspace Application Repository - https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/dev_model_and_contributions...
Dear Devzone:
I have setup done matter environment as blow:
NB: Ubuntu 22.04 with WIFI and BT, installed CHIP tool from official pre-built (V2.8.0 corresponding version...
Hello
Our customer makes IoT Product and use the Nordic 9160.
However the PCB Size is small.the 9160 SiP design in the PCB Top layer and Sim Card design in the Bottom...
Hello
As the title says, I am suspending the UART using PM_DEVICE ACTION_SUSPEND, but the power consumption is not decreasing significantly.
With CONFIG_SERIAL=n and no...
Hello. I'm trying to toggle a GPIO pin at a predefined frequency in order to measure the accuracy of out RTC clock. This code uses the GPIOTE, RTC, and PPI peripherals in...
We are evaluating the the NRF 5340 for a new project and we would like to know if the NVS implementation [1] provides protection against data corruption if the supply is unexpectedly...
Hi guys,
So, I've been working on a project for measuring liquid using the TDC1000 IC from TI which was running fine on STM32.
My experience with nordic connect sdk is...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
Our pre-production PCB power consumption still too high, so we are looking for a way...
