Good afternoon, I'm working on a project where the objective is to estimate the beacon <-> observer distance based only on RSSI. As a part of evaluation I've taken some RSSI...
Dear support team,
We need to add custom fields to the node database (CDB), as shown in the screenshot below:
Use bt_mesh_cdb_node_store(); to store, and then use the...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hi,
Sorry to be posting a lot about my LIS2DH12 on custom hardware lately. I do believe my different inquiries are to be treated as separate.
My (modified) hardware now...
Hi, I tested the TCP client AT command in nrf9160DK, I flashed the ncs v2.5.1 example of serial_lte_modem firmware on the board.
I send the command as below list:
AT#XSOCKET...
Hello All,
I am hoping someone can provide a recommendation regarding the matching circuit for my antenna using nRF54L15. Please see the attached schematic for reference...
Hello All,
I have nrf9610 Develoment Kit on my side:
mfw_nrf9160_1.3.5
Using nrfutil-device core version: 7.13.0
Using nrfutil-device version: 2.1.1
...
11 months ago in an answer a nordic member wrote (in regards to an error that I now also had and could solve using CONFIG_DEBUG=y):
[quote userid="81283" url="~/f/nordic...
Hi there,
I have an issue when using PPKII software on MacOS at 100ksps (no issue at 1K):
The 10min button at the top does not appear anymore
After a 3min measurement...
Good Afternoon,
I'm designing a 4-layer PCB based on an NRF52832 (QFAA) paired wit h a Molex 479480001 SMT Antenna, and I was hoping for some feedback on Antenna Matching...
Hello,
I'm trying to sniff packets with wireshark by varying the connection interval and supervision timeout of my ble application. I see that with lower connection intervals...
I'm presenting an issue when exporting the data collected, specifically the digital outputs, they are exporting incorrectly, but in the Data Logger tab they are presented...
Hello,
I'm encountering an issue while configuring the SPI bus to communicate with a LIS3DH sensor using nrf52832. I'm working with Visual Studio Code using nrfConnect SDK...
When implementing AWS_IOT provisioning by claim process, AWS_IOT responds to the published topic $aws/certificates/create/json with a 3580 byte response. This causes TLS to...
Hey, I'm pretty new to Nordic Development. I am working on nRF5340 Audio DK development board right now and I was trying to create a bluetooth speaker kinda setup using the...
Regarding the design issues with the nRF5340, I have adopted the nrf5340_qkaa_config3 design scheme from the hardware design package. However, after testing, I found that...
Hi nRF Community,
I'm currently delving into the bandwidth capabilities of LE audio (BAP Streaming), utilizing two nRF5340-DK (PCA10095 2.0.2) Dev-kits flashed with unicast...
Hello
For some reason the example doesn't work, am I doing something wrong?
In this example, there was no overlay file, which I made myself.
I use a sensor: https...
The spec says "Some electrical parameters are valid only for the TA operating temperature conditions. "
what is the " Some electrical parameters " here means?
what will...
Hi folks,
The blocking transmit function uart_poll_out() works as expected with UARTE, but not with UART.
For our project low power is critical. Thats why I need to use...
Hello everyone,
Here is the code I used to get my IP using DHCP,How do I use this IP to send and receive UDP or TCP? Using custom mac is this how I use it inside dts below...
Hello DevZone,
I am working in VS Code and nRF Connect SDK 2.6.0. Developing battery powered Zigbee device. I have an issue with FOTA - it started to rollback after update...