Hello,
I'm using two nRF9161 to communicate with each other and I want to test and measure the differences between the 3 modes available in SDK3.0.0. First, I configured...
I have tested the nRF Cloud Multi Service Sample using Quick Start and it works perfectly.
I am trying to build the sample so that I can make small modifications for an...
Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
Hello everyone,
We are developing products with nrf52840 and our default supply voltage is 1.8V.
Is it possible to program a custom 1.8V board with nRF52840DK?
We are...
Hi
I am using nRF52840 with SDK 15.3.
I have a project where I uses FatFS to write to a SD-card with SPI interface (SPIM3). This works very well.
I am now trying to...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with this specific exercise (l5_e2):
To ensure I wasn...
Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hi,
I just have a simple question => could you please tell me what are the ECCN numbers associated to this software:
www.nordicsemi.com/.../nRF-Connect-SDK
Thanks in...
-- west flash: rebuilding [0/16] Performing build step for 'tfm' ninja: no work to do. -- west flash: using runner nrfjprog -- runners.nrfjprog: reset after flashing requested...
Hi,
We are currently developing a solution where a Thingy91 acts as a BLE central. We have had a lot of issues with BLE when using the nRF52 as a HCI device being controlled...
Hi guys,
Maybe someone already did this work but if no:
I would like to take only the relevant parts to my project.
I am not sure what can be given up.
I need cellular...
Hello!
I would like to know what are the minimum, maximum and recommended current values for the VDD, VDDH, VSS and VBUS supplies. The voltage values are listed here...
Hello,
Im trying to flash RAYTAC AN54L15Q-DB board but im keep getting following error:
Error: One or more batch tasks failed: * 1050050051: [Probe] Emulator error: Failed...
Hi,
We are doing RF Test for nRF52840DK, and we are using CBT Bluetooth tester. Commands are going to CBT fro nRF board.
My Question is code we need to flash for RF test...
I am using the Nordic nRF5340 DK to communicate with the ICM-42688-P sensor via SPI. However, the sensor does not respond to the MCU's commands. After observing the SPI clock...
Hi,
Previously it was possible to download the old nrf5 sdks from for instance this url:
developer.nordicsemi.com/.../nRF5_SDK_v15 .x.x/
but it seems to not be available...
Hello,
I'm trying to read the build info of the Bluetooth LE controller using BT_HCI_OP_VS_READ_BUILD_INFO, but I get the following warning:
<wrn> bt_hci_core: opcode...
I am using nrf5340dk and I am facing an issue. I have configured SPI on my dev kit and the screen I am using with it is operating at 5v but the dev kit has 3.3v max. So I...
Hello,
I am trying to find a simple example of how to setup and run the SAADC on the nrf5340 in continous mode.
I would like to use the internal timer and only need to...
ZBOSS NCP: ZBOSS NCP Serial Protocol, Version 1.5 states that a "Full featured Zigbee PRO r22 platform is provided".
Is a more recent version of this document available...
The broadcast interval is 2s, and the power consumption is 7ua on the DK board; On this basis, the power consumption when using an external low-speed crystal oscillator is...
