Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hi, I tested the TCP client AT command in nrf9160DK, I flashed the ncs v2.5.1 example of serial_lte_modem firmware on the board.
I send the command as below list:
AT#XSOCKET...
Hello All,
I have nrf9610 Develoment Kit on my side:
mfw_nrf9160_1.3.5
Using nrfutil-device core version: 7.13.0
Using nrfutil-device version: 2.1.1
...
I am developing an MQTT client application with NRF9160, trying to connect to a Mosquitto broker using TLS with three certificates. However, I am encountering an SSL version...
hi support team,
in 9161dk, when we need to program external flash, we need to config board with nrf connect, may i ask what's this? and if i need to consider power consumption...
Hi, We are using nrf9160 and building the application with CMSE. When my program accesses dynamically requested memory (address 0x200128b0), the program automatically jumps...
Hi
I tried to run the sample "hci_pwr_ctrl" from the NCS v2.7.0 on the nRF54L15.
After starting the sample, the modification of the TX power level during the advertising...
I am trying to make my gateway send stereo data to the headset where it will be played on an external codec. I want this to be a single stereo stream.
I had this working...
Hi We are running the nus service on our device and would like to use a PC to connect to this service.
What is the best way to achieve this ?
I've looked at the nrf52840...
1. Can I use the sample source (nRF5340 Audio) on another board?
2. Is there a way to develop without using the sample source? If so, how?
3. Is the LE Audio sample source...
Problem Description: I am trying to configure and control an LED connected to pin P1.07 on my nRF52 device, but I am experiencing issues. When I configure pin P1.07 as an...
My goal is to test Net Core updating so, if needed, I can update the Net Core.
I have my app set to boatload both the app core and net core using external memory but when...
Hi
I'm using asynchron UART.
For example, I defined idle time to 20us.
It works without any problem.
#define RECEIVE_TIMEOUT 20
static uint8_t rx_buf[512];
ret...
Hi there,
I need help finalizing the size of my product's settings partition. I only store Bluetooth bonds on the settings partition: 20 bonds to other Nordic devices via...
Hello,
I'm abit confused... while the reference is +/-0.6V and absolute ratings are not to go below VSS=0
so is it SAFE to measure -0.5V with the ADC?
it looks like...
Hi there,
At the moment, we have developed a custom PCB and are having wireless troubles. Our suspicion is that the crystal circuitry must be the issue as there is absolutely...
So i have a problem with documents for nrf52820 while it's a great chip with good functionality i selected it mainly because all of product details and specifications told...
Hi,
I upgraded Toolchain and SDK in VS Code to Version 2.6.1.
Now the build is failing.
As far as I can see the wrong CMake will be used - from Visual Studio but it...
Hello,
I'm trying to implement the MCU BOOT in order to introduce the Firmware uptdate but I get the following error:
I'm trying to reduce the RAM usage but with no...
I am new to BLE development and was wondering how I can read the data published by the A&D Medical Blood Pressure Monitor with the nRF5340 acting as a central. I can connect...
hi support team,
customer reported on problem that one product is ok when in factory, but now is in problem after delivered to office.
i had onsite debug and find out...
Hello,
I am practicing the intermediate Nordic Academy online course, and I have a problem of the thread viewer.
I have enabled debug, I did everything strictly according...