Hello,
What is the max data size for NUS?
According to BLE data throughput in the S140 document, it looks like 247 but the data was sent successfully with NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Dear Sir :
We are now developing on nrf52840, with ncs v2.6.1 and zephyr.
We want to put I2C0 to PM_DEVICE_ACTION_SUSPEND before sys_poweroff().
Our code is below :...
Hello,
We made some custom boards for our project using NRF52805. following is a schematic of it.
My first aim to print "Hello world" on RTT every second. For that,...
while reprovisioning NRF-9160DK if i try Create JITP Certificates following issue observed.
There was an error generating the certificate: A Nordic Semiconductor product...
Hi,
I am implemented the uart functionality, I'm getting below issue.
[00:00:00.445,526] <err> Throughput: Failed to set UART callback (err -88) [00:00:00.445,556] <err...
I am in the process of bringing up a custom board with an nrf5340 and a FUSB302B USB-C PHY-controller.
As a driver for the FUSB203B, I am using this project as an OOT-module...
I have developed the low-level drivers for the MT29F4G01ABAFDWB (using spi) NAND flash and am currently using the Zephyr RTOS. I would like to integrate FATFS into my NAND...
I used a script to write the Gateway and Headset to the nRF5340 Audio DK board.
I used VSCODE to write the Gateway source and Headset source to the RAYTAC board.
I tried...
We have a problem where a display running on 5V with an UART on 3.3V will self-bias through the UART TX pin when the 5V supply is switched on.
How do you make zephyr not...
Hi,
We are using nRF5340 DK and the nRF Connect SDK Version 2.6.1.
We are developing a mesh network. Our requirement is the one device can connect to three other devices...
Hello.
What is correct way to use AT%MDMEV commands(searh status) to establish connection after long PSM/sleep time (168h). Our devices are used to track wild animals so...
Hello,
I'm encountering persistent address conflict issues within my Nordic project.
Occasionally, when a device joins the network, I observe address conflict errors....
Hello,
I am trying to send an array which has 2048 bytes via UART. But, when I add a some delay to repeat the the UART transfer, the code gets stuck on the HardFault. I...
Hi Community,
I report this issue in github, it seems nobody reply me, so I ask here again.
lesson 8 exercise 3 solution build failed · Issue #9 · NordicDeveloperAcademy...
Hi,
in our application we use SDCard and USB stack with the following configuration:
The communication with the nRF5340 is done by using a Linux Embedded systems. When...
I think that the source of the nRF5340 Audio DK sample board is designed so that LED1 lights up when a connection is established with CIS.
We are thinking of connecting...
Hi, The Kconfig fragment CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU is awesome to quickly get BLE OTA working. However, when going in depth, we can see that it's implying:
...
Hello,
I am using the ADC on my custom board, based on nRF9160.
I am getting correct results when measuring a known voltage. However, I noticed that the execution is very...
At the company I work for we are developing a keyboard with mouse capabilities via USB and BLE using the NRF5 17.1.0 SDK. We create the USB HID with the following SDK macro...
When using the nRF9160-DK, I flash the board with Asset Tracker V2 as provided by the instructions for the board here .
The board and SIM card are registered and the board...
Hi,
I am using custom board (nRF9160) and zephyr V2.6 and I would like to make sure that I understand the ADC settings correctly in the device tree:
channel @ 1 {
...
Hi there,
I have just tried to migrate to a new M2-based mac book pro and everything went OK (i am able to build and run my sw on the target) except that I don't have any...