Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hi everyone,
In nRF9160 with ncs 2.9.0 I've problems when trying publish a MQTT payload bigger than 2700 bytes aproximately. In advanced I already was adequated buffer size...
Hi, I've recently acquired an nRF54L15DK, and started the development on BLE, I'm fairly new to Nordic's enviroment. In the last couple days I've been trying to build the...
Hi everyone,
I use the ble-app-buttonless-dfu example to develop my application.
I make a mutual authentication to be sure the device is connected to the right mobile...
Dear Nordic Engineers
The following documents are our hardware designs. When we conducted the test, we found that we couldn't obtain the GPS satellite signal and the 4G...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Hi.
For a while I have had some issues with the toolchain when using the nRF connect SDK in visual studio code on windows 10. I believe it was after installing SDK version...
Hello Team, We are currently using the nRF52833-QDAA-R SoC for our R&D activities and have assembled the board based on Configuration 6 . However, we encountered an issue...
I followed the steps here docs.nordicsemi.com/.../building.html: PS C:\ncs\v2.9.1\nrf\applications\nrf5340_audio\tools\buildprog> python buildprog.py -c app -b debug -d gateway...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
Hello,
I'm developing for nRF54L15 the application with the NSIB + MCUBoot. I have a problem with fprotect in mcuboot returning EINVAL error. That happens due to limitation...
We aim to use an external Cellular module for MQTT communication.
I found that the nrfxlib/nrf_modem library is only supported for nRF9x series MCUs. Does this support...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
We want to evaluate the Bluetooth: nRF Distance Measurement with Bluetooth LE discovery functionality. But we only have nRF5340 Audio DKs. Not ordinary nRF5340 DKs...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
When flashing with SDK v3.0.1 the following error occurs:
-- west flash: using runner nrfutil -- runners.nrfutil: mass erase requested -- runners.nrfutil: reset after flashing...
I'm not sure if this is the right place for this question.
I'm using the Settings subsystem for the BLE name.
When BLE is initialized inside matter, settings_load is only...
Hi,
I'm using an nrfx_timer event with k_poll_signal_raise to trigger a thread to perform an operation.
I've noticed around 900ms delay between when the signal is raised...
Hello Nordic support team,
Forgive me if I am asking a stupid question.
In the source file ble_conn_params.c, there is a function called ble_conn_params_init() and I...
