Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Hi:
I purchased the nRF5340 Audio DK and used NCS 2.5.0. After flashing the unicast_audio_client example (zephyr/samples/bluetooth/unicast_audio_client), it failed to run...
Our project is built wit NRF Connect SDK 2.9.0. For the UART we use nrfx_uarte library directly.
RX works perfectly, but TX is working only in blocking mode. If I call ...
Hi,
I designed a custom NRF52832 board and need to connect it to an ESP32 board. I soldered five boards for testing and also have an NRF devkit.
However, the ESP32 only...
My platform is the NRF5340 , coupled with 32MB of external flash , so I have plenty of external storage available. However, there's a risk that my project may eventually outgrow...
Hi there,
we're currently in the process of changing our hardware to use the nRF54L15. Since all the security regulations are getting stricter and stricter and the support...
I'm looking at Product Specification v1.2 - Reference Circuitry Configuration 2 where BUCK2 is not used. The schematic shows the output VOUT2 is tied to VSYS in this case...
Hi Nordic Team,
I am planning to develop a Matter-over-Thread end device (sensor) using the nRF54L15 , which will be battery-operated . To maximize battery life (minimum...
Does anything exist yet? The datasheet only contains a preliminary matching network and says will be available when the chip enters mass production, but nothing is available...
I tried used Nordic's UART service implementation as a starting point and everything works but I can't figure out where the string "Nordic UART Service" from "nrf connect...
I have loaded the Quick Start Application using nrf connect for Desktop after following the instructions. I get the error as per the attached file on the Serial Terminal....
Hello,
We are trying to test our custom board with nRF9161 in a new location, so we bought local SIM cards (Yettel, Serbia) here. These are not special nb-iot SIMs, just...
Is there a way to modify the distance measurement sample code to where it is intended for one transmitter and multiple receivers versus between just two devices? I am trying...
The workaround says:
" Trigger TASKS_PLLSTART before TASKS_XOSTART is triggered and trigger TASKS_PLLSTOP after TASKS_XOSTOP is triggered."
I would like to start HFXO...
Hi,
I am running into a really strange issue where setting both CONFIG_NRFX_PWM0=y and CONFIG_NRFX_PWM1 =y in prj.conf gives me the following build errors while using mcuboot...
Hello,
My PPK2 is reporting 2 zetta amperes power usage, and I found out that the "modifiers" appear really broken:
I have attempted to re-flash the ppk2 firmware, but...
