Hello,
I am using the same hardware, and firmware on 4 custom boards of the same device. I observed that I am getting different current consumptions in each devices.
I...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi there,
we're currently in the process of changing our hardware to use the nRF54L15. Since all the security regulations are getting stricter and stricter and the support...
I'm looking at Product Specification v1.2 - Reference Circuitry Configuration 2 where BUCK2 is not used. The schematic shows the output VOUT2 is tied to VSYS in this case...
Hi Nordic Team,
I am planning to develop a Matter-over-Thread end device (sensor) using the nRF54L15 , which will be battery-operated . To maximize battery life (minimum...
Does anything exist yet? The datasheet only contains a preliminary matching network and says will be available when the chip enters mass production, but nothing is available...
I tried used Nordic's UART service implementation as a starting point and everything works but I can't figure out where the string "Nordic UART Service" from "nrf connect...
I have loaded the Quick Start Application using nrf connect for Desktop after following the instructions. I get the error as per the attached file on the Serial Terminal....
Hello,
We are trying to test our custom board with nRF9161 in a new location, so we bought local SIM cards (Yettel, Serbia) here. These are not special nb-iot SIMs, just...
Is there a way to modify the distance measurement sample code to where it is intended for one transmitter and multiple receivers versus between just two devices? I am trying...
The workaround says:
" Trigger TASKS_PLLSTART before TASKS_XOSTART is triggered and trigger TASKS_PLLSTOP after TASKS_XOSTOP is triggered."
I would like to start HFXO...
Hi,
I am running into a really strange issue where setting both CONFIG_NRFX_PWM0=y and CONFIG_NRFX_PWM1 =y in prj.conf gives me the following build errors while using mcuboot...
Hello,
My PPK2 is reporting 2 zetta amperes power usage, and I found out that the "modifiers" appear really broken:
I have attempted to re-flash the ppk2 firmware, but...
Hi,
We have come across AT%XRFTEST command problem for TX test on nRF9151 EVK. We have used nRF9151 modem firmware version 2.0.2 and executed following AT command on nRF9151...
I am trying to format an external flash chip with littlefs, but keep getting an MPU fault. I can erase the chip, but not mount or format. I have tried writing and reading...
I'd like my VS Code build configuration for my project to be included in version control.
It seems like this configuration is stored somewhere in the "build" directory that...
Description:
I encountered an issue where my NRF54L15DK development board fails to connect to my Windows 11 PC. Upon plugging in the board, the LED near the debugger starts...
