Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
My team was looking to transfer a 20-byte value (or 'message') between a mesh client and server, what is the best way to achieve this? I have practiced with the light_switch...
Hi,
I am currently developing an application for the NRF52840 using a custom pcb powered through the VDDH pin using a 4.2v lithium ion battery. Part of my application requires...
Hi,
I am trying to following the instructions at: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.iotsdk.v0.9.0%2Fiot_sdk_user_guides_java_coaps...
I have configured the dev kit by cutting the SB9 bridge. I am powering the device from the J2 USB port on the DK. I have not bridged SB12 or SB11 as I am powering the device...
Hello all,
I am experiencing a ~5uA oscillation (between 5uA and 10uA) in sleep mode, DC/DC converter enabled, no RAM retention. The total current is of the entire system...
i am working with jlink segger edu, in a custom board, it dont have swd TX, RX pins connected, only jtag pins. I Need to see if my gps conected throw uart is working or not...
I configured the pca63519-sr3_nrf52832_shield to fit on my board (actually disabled all peripherals, only the bluetooth protocol part), but found that the modified code could...
Hello! I wrote about the details in topic 66156 , but they did not answer me, because this question is already different from the original one. The drv_rtc.c library has this...
HI,
I have been facing a few issues with the BLE custom service, I am looking to create a Pedo meter service which displays step count information received from the sensor...
Hi Guys,
We have designed a custom board which is using BMD350.
Our application requires using the BMD350 in beacon mode and then going to sleep in low power.
We have...
I can listen for radio inactive event according to this post https://devzone.nordicsemi.com/f/nordic-q-a/9137/change-advertising-every-time-event but I am scanning at the...
Hi everyone,
I want to assign the DEVICEID to System ID characteristic (which is under Device Information Service). DEVICEID is a 64bit and I found that I could assign this...
Hello,
I am developing a sensor like a beacon. I want to measure the distance from the node. I record the RSSI sample for a few seconds and average it to stabilize the value...
Hi,
Can anyone confirm the advert sent in the attached is not corrupted in anyway? as I seem unable to scan my device with anything other then nRFConnect.
The Bluetooth...
Hello,
I found some some threads on similar questions but none answered mine, so here it is:
I try to use UART between nrf52840 and another chip. When the other chip resets...
