Hi,
We have a working firmware that uses LTE-M for network connectivity to connect to NRF Cloud. But upon testing with NB-IoT configuration (CONFIG_LTE_NETWORK_MODE_NBIOT_GPS...
If I try to compile any of the WIFI examples for the Thingy91x I get a RAM overflow error. The only exception to this is the WIFI scanning example. If I build these for any...
Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
we want to use NPM2100 with 2.4V rechargeable battery, burst 2.4V to 3.3V @150mA.
there are a sepcial charger solution for the 2.4V rechargeable battery .
Could Nordic...
Hi everyone,
I'm new with nordic chips and for our project we use a custom board based on the famous nRF52840 mcu. I read a lot about SDK17 in the infocenter to find how...
Hi
The latest OpenThread/Zigbee SDK has no examples for openthread with the PCA10059 (No MBR, executing directly from 0x0 @ flash start).
Ive tried now multiple times...
nRF52840, SDK 16.0.0, SD132v7.0.1
What's the correct way to tell whether HFXO or HFINT is clocking the HFCLK controller? I'm able to start and stop the HFCLK controller...
Hi, i am using the nRF52dk would and im using the pwm driver example and im trying to understand the way the seq_values void works when it comes to phase or sequence would...
Hello, I uses the NORDIC project saadc_low_power. A counter was built into this so that only a defined number of samples are carried out. Measuring current on an nRF5 DK while...
Hi,
I have a custom PCB using the Johanson 2450AT18A100E chip antenna. For some reason, I'm getting extremely subpar RF performance and so I'm taking a second look at...
Hi I have a nrf5340 pdk version 0.8.0 (PCA10095) When I plug it into my Win 10 (latest version 2004) device manager tells me it sees 3 comports
When loading the 'Peripheral...
I want to change between LTE-M and NB-IOT, however lte_lc_system_mode_set(); is not actually changing the mode.
I am doing something like this
I can't rely on PSM/eDRX...
Hi Nordic:
Because my device(peripheral) sometimes is connected by a unknown center device, I want to get some information from this center device,
and try to find it...
Hi,
I have just added a VS service (PCA10040, s132 7.0.1, embedded studio v5.10a x64)and I understand I need to increase the ram given to the softdevice. However, I have...
Hello,
We are developing a product using a nrf52832 and an APDS-9306 ambient light sensor. This sensor interface using the TWI peripheral. We are using the 14.2.0 SDK and...
Hello,
I have a problem building Asset tracker from SDK application example with simulated GPS data. After building an error message shows.
B 48 KB 132.29% B 64 KB 13...
Hi, I have started development on nRF52840 DK. I have 2 boards one is working fine but the other one making an issue. When I tried to connect it shows the following error...
When using the sd_ble_gap_sec_params_reply function to reply to a pairing request and declining it with the BLE_GAP_SEC_STATUS_TIMEOUT reason, nothing seems to happen, the...
