Hi, I am fighting with a bug I found in SDK v2.8.0 for BLE scan filter on a test project as follows: 2 Devices (Ezurio BL653-DVK using the nRF52833), both having central and...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
hi,all
i am a new learner about the BLE
when i use softdevice 17.0.2 to run the example (anyone) ,there is no problem.
then I want to use the SDK12.3.0 to run a formal...
hi
I am using nRF52832 and mesh sdk V4.2
I have modified the light switch example in order to send 1 byte of data instead of the on-off commands. in the server side I...
Hi,
I have a problem with coap response. I use iot coap library.
Client send nonconfirmable coap message with payload to broadcast addr
Server get payload and send nonconfirmable...
I am getting the Following error after connecting the JLink
I followed the following procedure
What am I doing wrong? DO I need to install anything else?
Hey All,
I ran into an issue on the nRF Connect SDK trying to get a nRF52840 advertising using CODED PHY. I figure it's not fully implemented yet are there any updates on...
I advertise as
BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE
BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED
This posts suggests I may have not really disabled...
I am using an NRF53 DK board with nRFConnect/Zephyr 1.3.0. I need to define the UART pins I will use in a .overlay file but I would like to NOT define any flow control pins...
Hey
I am working on nRF51822 SDK12, S130
I have encountered a problem when connecting and disconnecting from the device at a fast rate, occasionally comes an event in...
Hello,
We integrated latest released version of "pc-ble-driver.py" & "nrfutil" in our custom linux os running on ARM 32bit based custom board (B1).
pc_ble_driver_py :...
Hello,
Our design uses Laird's BL652, which uses nRF52832. I need to calculate the maximum clock drift of timers given the crystals used in our design. Our application uses...
Hi,
When I tried to use BLE5.1 phase data to achieve direction finding, I found a phase shift between reference period and the first slot, as the below graph shown:
...
Hi DevZone!
I would like to use nrf9160 for sending/receiving data by interfacing it with my microcontroller over UART and sending AT commands. I have a nrf9160 Feather...
Hello, support team.
In my SDK, I created two app timer.
What I expected is
- 1st handler called every 1 msec.
- The other handler called every 100 msec.
But...
This "BUG" is observed on nrf52840 DK (chip version is version 2 from *(UINT32*)0x10000134UL).
When NRF_RADIO is set to TXADDRESS 0 and RADIO_PCNF1_WHITEEN_Enabled...
...
Hello,
I am using VS Code 1.48.2 and building the C++ application code on nRF52840 dev board using "west" commands.
I have the following structure
project_directory...
