Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Is there any new information released about the GPS current consumption of nRF9160? I want to estimate the battery lifetime of a 1000mAh battery running the asset tracker...
Hi,
I am under long run test between coordinator and end device.
End device sends a message and goes into system off state until next event(door open) for minimal power...
Hi Everyone,
I am having problems writing to an array in NRF52832 without causing the program crashing at run time.
I declare the array to be 512 uint8_t long
then...
hi, I'm a fresher of this kind of development. My boss give me a board and let me run the Zephyr OS on it. But I am not sure whether I lack some things and how to assembly...
hello I am just needing some clarification on meshing. I am using the long range nfr52 chip. I have a transmitter with a tilt switch that connects to my receiver when connected...
Dear Support team,
could you please advice how can I change the endpoint where Thingy91 sends the measurement data stream from the sensors?
By the default it it is the...
HI, I'm Rafael Fajardo a student at Las Palmas de Gran Canaria University . I am using the nRF51 Dongle and following the Sniffer User Guide, but when I got to the final step...
Hello,
Zephyr has their own Bluetooth stack. Has anyone done an objective comparison of the Zephyr stack to the NRF52 soft device stack? I am very familiar with the soft...
Hi,
I'm currently making energy measurments with an nrf9160 DK. The software project is based on the udp_with_psm sample. I would like to run the test on different tx-power...
When debugging with Keil, the software may suddenly start from the beginning. The reset process may be running somewhere, but it cannot be detected. Is there information that...
Hi everyone,
I am a beginner developer, I'd like to know what's the difference between different softdevices.
In particular I am using SDK 10.0.0 with softdevice 110...
Dear Sir,
I am using Example beaconing_nrf52840_xxAA_s140_6_1_0 in nrf5 SDK for Mesh_v3.0.0 get stopped after running for sort period. I have tried to debug but could not...
Hi,
sd_ble_gatts_hvx returns 13313 in some rare cases involving the phone is far from the nrf52840.
My questions:
1. What this return code means?
2. What is the recommended...
I am trying to connect the device to android phone both on nRF connect as well as normal pairing. Both seems to not work.
I get this log from the device:
on_ble_evt: BLE_GAP_EVT_DISCONNECTED...
