Help Needed: BLE Not Working on nRF52810 (Tried Zephyr & nRF5 SDK)
Hi everyone, I really need help getting BLE working on my custom board with the nRF52810 . I've been trying...
Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
Hello,
I'm trying to make the nrf5340-DK capable of connecting to BLE from multiple devices.
The program is based on: Bluetooth: Bluetooth: Peripheral UART .
I found...
Hi all,
I am trying to interface HI-3585 with nrf52832 through SPI which works fine. Now i have merged the code with saadc program so as to transmit adc values through HI...
Hello.
I am building nRF Mesh SDK using cmake (gcc).
After successful building the code, I flashed hex file to nRF 52 DK.
I want to know free space in DK after flashing...
We want to use nRF52840 as advanced USB - UART converter to control end device (see structure below).
We already checked that our end device is working fine by external...
Dear Support
I’m having a problem erasing the network configuration data in the flash.
We are using nrf5_SDK_for_Mesh_v2.0.1 with the flash manager according to this post...
I am new and trying to install and run samples on Raspi 3B but cannot. Have anyone worked with Raspi 3B and nrf52840 dongle and please give me some instructions.
Hi I'm using Android Studio 3.2 and github.com/.../Android-nRF-UART My Samsung SM-G570Y (Android 7.0 API 24) works no problems but the Samsung SM-G955F (Android 8.0.0, API...
Hi. I am developing a gateway using SDK15 and nRF52840.
I'm advertising 4 devices every 20ms.
Theoretically, it should be scanned 50 times each, but in reality it is...
I tried to add an additional characteristic to NUS service as below.
However, any mobile apps could find only existing Nordic Rx and Nordic Tx characteristics, other than...
- Go to the following link:
www.nordicsemi.com/.../
- Scroll down the page and click the "Downloads" tab
- Go to the nRF52840-DK-HW tab and click "Download file"
...
Dear Nordic Team
-> what is the pinout of the TRACE connector of the nrf52840DK (PCA10056) board ?
I need to connect wires onto P0.11 and P1.00 GPIO, and the trace...
I'm using the nRF52832 SoC through Rigado's BMD 350. For initializing BLE, I'm using the Thingy52 firmware code as the hardware mostly reflects that of the Thingy52. My hardware...
Hi,
I am using nRF_SDK_15.0.0_a53641 and writing a program with keil.
I am receiving data from the sensor with TWI communication and writing it to the sensor by SPI communication...
Hi everyone,
Device : nRF52832
SDK version : 14.2
Softdevice : S132 v5.0
I am facing a problem when changing the interrupt priority dynamically. Let me explain the...
HI,
I'm currently working with two chips RF24L01+.
Each chip switch in sending role to receiving role several times. By default, I set them in sending role and I whait...
Hello
Previous projects used SDK11 protocol stacks with BootLoader and DFU
About the BootLoader of sdk11, DFU is different from sdk15. Please consult me. Thank you.
...
