Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi,
I am working on RTC implementation. I had a doubt.. Is it possible to generate interrupts on different channels (channel 0/1/2/3) using same RTC instance ?
Thanks
Hello,
I'm trying to communicate with another device via I2C. I'm trying to do a simple write but it seems that the TWI NRFX driver is sending wrong data.
I'm just calling...
Hi,
I am implementing a beacon solution and intrested to move from fast to slow and vis versa(slow to fast) advertising modes -
i.e. BLE_ADV_MODE_FAST & BLE_ADV_MODE_SLOW...
Hey,
I have seen some articles which says that voice over BLE (4.0) is possible but there is no standard profile for it.
So far i've seen :
Silicon Labs
STM
T.I...
Hi,
After I reset nrf8001, RDY pin stays hi. I checked the crystal pin, there is no clock. I am using TSX-3225 from Epson with 12pf caps.
Am I suppose to see the clock...
Hi,
I am working on a new project with the secure bootloader (SDK 15) as a part of it. I want to add periodic task that will do several actions for example maintaining the...
Hi,
I am downloading my code to my custom board and sending commands through a USB virtual COM port. I basically echo and execute some GPIO operations after decoding the...
I have installed NRF 5X command line but I don't see it in my programs/start / desktop where will be the .exe file or how can I open that? How can I work with that ?
Hello ,
I am using 4 nrf52 DK for Mesh
1. how to I configure a Node as Relay
2. How do I capture MESH Packets/ Data from Mesh in Raspberry Pi and send to cloud
hi,
When working with Keil are the NRF_SDH_CLOCK_LF_RC_TEMP_CTIV & NRF_SDH_CLOCK_LF_RC_CTIV compiled as part of the nrf52810_xxaa project?
if not how can I compile...
Hello, is there a way to send messages via the mesh transport/access layer (not using client/server models) but still be Bluetooth SIG compliant? where can I find information...
Hello,
There are a few posts about EasyDMA consuming 1-2mA of current, and I've measured similar currents. In the nRF52832 product specification, this appears to be one...
Hello,
I am running the ble_app_beacon example and want to add battery percentage in the advertising packets, how to do that. And is it possible for ble_app_beacon example...
I had planned on using the nRF52840 I2S peripheral in Nordic Master mode to either produce a 31.25 kHz sampling rate, or a 62.5 kHz sampling rate for my application.
There...
How do I make my phone to auto connect to my nrf51822 device when it is within range ? I dont want to keep having to tap connect on my app. (android and IOS)
