Hello, I am following the instruction on dev academy - nrf connect sdk intermediate lesson 2 excercise 1, but I can't select data tab on memory explorer.
I can select only...
I have a Raytac MDBT50Q-CX and cannot seem to flash it correctly. The flash succeeds, but the device is no longer recognized by Windows or (raspberry pi) Linux.
My goal...
Hi community,
I need to get data from the BMI270 sensor that is on the Thingy:53 board. I have already taken some previous topics as reference but I still haven't been successful...
Hallo.
I am working with Thingy.91x and after learning almost all lessons with Nordic Dev Academy, LTE fundamentals, i have encountered an issue.
Right now I can't use...
I am having problems flashing my custom board with a nrf5340 chip. Sometimes it works, sometimes it does not, but more often than not it doesn't work and I cannot figure out...
Hi，
When I use NCS V2.5.0 （board：nRF 52840），I want to set the Non-Connectable and Scannable Extended Advertising.My code as follows.I use the APP nRF Connect for moblie...
Hi Nordic team.
I'm finding a way to update the factory data over-the-air. Specifically, I want to update the Matter Certification information (PAI, DAC, ...) over-the-air...
Hi,
I just have a simple question => could you please tell me what are the ECCN numbers associated to this software:
www.nordicsemi.com/.../nRF-Connect-SDK
Thanks in...
-- west flash: rebuilding [0/16] Performing build step for 'tfm' ninja: no work to do. -- west flash: using runner nrfjprog -- runners.nrfjprog: reset after flashing requested...
Hi,
We are currently developing a solution where a Thingy91 acts as a BLE central. We have had a lot of issues with BLE when using the nRF52 as a HCI device being controlled...
Hi guys,
Maybe someone already did this work but if no:
I would like to take only the relevant parts to my project.
I am not sure what can be given up.
I need cellular...
Hello!
I would like to know what are the minimum, maximum and recommended current values for the VDD, VDDH, VSS and VBUS supplies. The voltage values are listed here...
Hello,
Im trying to flash RAYTAC AN54L15Q-DB board but im keep getting following error:
Error: One or more batch tasks failed: * 1050050051: [Probe] Emulator error: Failed...
Hi,
We are doing RF Test for nRF52840DK, and we are using CBT Bluetooth tester. Commands are going to CBT fro nRF board.
My Question is code we need to flash for RF test...
I am using the Nordic nRF5340 DK to communicate with the ICM-42688-P sensor via SPI. However, the sensor does not respond to the MCU's commands. After observing the SPI clock...
Hi,
Previously it was possible to download the old nrf5 sdks from for instance this url:
developer.nordicsemi.com/.../nRF5_SDK_v15 .x.x/
but it seems to not be available...
Hello,
I'm trying to read the build info of the Bluetooth LE controller using BT_HCI_OP_VS_READ_BUILD_INFO, but I get the following warning:
<wrn> bt_hci_core: opcode...
I am using nrf5340dk and I am facing an issue. I have configured SPI on my dev kit and the screen I am using with it is operating at 5v but the dev kit has 3.3v max. So I...
Hello,
I am trying to find a simple example of how to setup and run the SAADC on the nrf5340 in continous mode.
I would like to use the internal timer and only need to...
ZBOSS NCP: ZBOSS NCP Serial Protocol, Version 1.5 states that a "Full featured Zigbee PRO r22 platform is provided".
Is a more recent version of this document available...
The broadcast interval is 2s, and the power consumption is 7ua on the DK board; On this basis, the power consumption when using an external low-speed crystal oscillator is...
