On the nRF54L15, how can I update the maximum TX time to 17040 µs when using Coded PHY?
I'm currently testing with the Throughput sample in nRF Connect SDK v2.9.1. During...
Hi,
I'm currently working with the Thingy:91X and would like to measure the total current consumption of the entire board using the PPK2. I understand that the PCA64165...
I'm not sure if this is the right place for this question.
I'm using the Settings subsystem for the BLE name.
When BLE is initialized inside matter, settings_load is only...
While using the nRF9151 DK , after inserting the onomondo sim and connecting, the Cellular Monitor SIM sections appears the Wireless Logic ICCID number instead of onomondo...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
I am using the GCC DFU project provided by Nordic on GitHub ( devzone.nordicsemi.com/.../)
I altered the main.c to trigger to DFU mode based on the contents of the GPREGRET...
I'm trying to connect a camera module ( OV7670 ) to my nRF51822 EK. The camera requires an operating current of 18mA. If i were to connect the 3.3V rail input for the camera...
I have code that uses two GPIOs to program an NRF51822 via SWD mode. This code all works fine and suceeds in programming the device.
What I would like to do is get the...
How can I relocate or manage the transition between the bootloaders interrupt vector map and the applications interrupt vector map which will be at different addresses in...
Hi !
I'm completely new into programming this device.
I downloaded the nAn-36 source from Github and I'm trying to make it work on a PC10000 dongle.
The code stops in the...
Hi,
I wonder if there is any way to disable the Rx FIFO so that I don't have to fill it to generate an event, since I need exact timing for every incoming byte.
Also,...
Hi, I am trying to connect N51422 server to anther vendor's client... the devices always disconnect after 30 seconds of connection.
I found that the reason of the disconnection...
I have seen this question asked on this forum in several ways but none of the parameters match up to my specific case. I am getting this error when I try to run the example...
Hi,
I load the s110 softdevice (I tried many versions 5, 6 and 7)
When I load my app on the SOC using Keil and the nrf_xxaa_s110 (256) target, the app doesn't run.
I'm...
Dear Nordic Developer Zone,
I have implemented a real-time-clock using application timer which is based on the on-chip real-time counter on NRF51822.
A concern of mine...
I'm trying to get the Nan-36 example working on my PC10001 board and I'm having some trouble. I've tried using both SD110 version 6 and 7 with appropriate (I think) memory...
Hi,
Is there any connection/disconnection API in ant+ (sd210) similar to BLE?
I want to use this to control the device activity cycle, if I get disconnection event, would...
Hi,
I'm trying to implement a specific communication protocol using the SPI on a nRF51822. The SPI on nordic side will act as slave. When CSN line goes low, I will also need...
Hi,
I currently have a problem with the continous scanning mode. I implemented the scanning mode that my device searches for the first 4 seconds after power up then picks...
Which example projects are compatible with s110 v7 for nRF51822?
I keep running into samples requiring "Legacy Keil" to be installed.
I just want a clean s110 v7 example...
