Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
Hi everyone again,
We have a custom board using nrf52840. We upload a bootloader with J-Link. https://github.com/adafruit/Adafruit_nR ... 40_express But we have a problem...
I am working on a project, using nrf52840 as a BLE Center to connect to BLE HID devices, but every time the connection is automatically disconnected when the service is discovered...
I have implemented a Peripheral on an PCA10040 based on one of the SDK (v15) examples. When using nrf Connect with a nRF51 dongle I can connect to the peripheral and interact...
Hello !
1. Do you have examples for nRF52840 what is demonstrate encryption/decryption packets on the fly as it explained in PS chapter 6.4 ?
2. What about examples for...
I have a Jtrace which I use over ethernet.
Running nrfjprog shows:
nrfjprog -f nrf52 --eraseall ERROR: No debuggers were discovered. NOTE: For additional output, try running...
hello, im using nRF52840, pca10056, I was using the example ble uart from examples\peripheral\uart im planning on replacing the use of "putty" PC application with a program...
Hello, i did my own custom board with a nrf52805 and now I did one custom first she is working fine so I decided to do the same but I can't see my device in nrf connect app...
Based on the "system_off" example, I intend to use the RTC to wake the device up (a NRF52840) periodically every minute.
I setup the RTC with LFCLK (32KHz) to trigger a...
software: ncs v1.8.0
hardware: my test nrf52833 board, with 9 antennas.
I do experiment like this:
aoa rx: in "nrf52833dk_nrf52833.overlay" file, I set " dfe-antenna...
Hello,
I am trying UDP sample with a local SIM (Orange) to check eDRX settings following this ticket .
Carrier said i should set an APN. This was not needed with 1NCE...
I try the new save to CSV feature in v3.4 power profiler.
I try to save all, but it says 0MB.
The sample rate is 100ksps, and duration is 301 seconds, but would result...
Hi, I have the following code in main.c:
If I initialize the beacon advertising first, which is the shown configuration, I get fatal error code 8 out of ble_advertising_start...
I have recently updated the SDK for my application from version 13.0.0 to 17.1.0, everything seems to be in order except for this function in nrf_drv_twi.c called twi_clear_bus...
the updated version of nRF connect v3.8 , for desktop , app - programmer doesnt recognize the device . i downgraded to 3.3v this version selects my device .
