This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Dear Sir.
I am using the cJSON driver .
When it comes to string it works fine .
However when I use integer and swap the lines
//cJSON_AddStringToObject(root, ...
I'm sorry my English is not good enough.
I am developing a product that works as a BLE peripheral using nrf52832 and NCS1.6.1.
In addition, the following statement is...
Hello,
I am trying to establish a mesh network with two nodes(self provisioned) simulating the Light and Light_switch examples without the provisioner. My plan is to play...
Fairly new to nRF Connect SDK & Zephyr although I have worked a lot with NRF5 SDK
I'm at a bit of a dead end here. I trying to setup a way to repeatedly read out data from...
Hello,
I would like to use littlefs in out Project and it seems to be very usefull. I read several documents and have the sample running on the eval board. But there is...
Hello,
I'm using the power profiler to perform current measurement of our IoT device. It appears to work well when running for a few minutes capturing. When I wrong for...
I am trying to use SPIM2 on an NRF52840 based board. The SDK is 17.0.2.
For the life of me I cannot understand how to 'consistently' determine the values to be specified...
I'm trying to modify the HTTPS sample to connect to Google Cloud Functions but I keep running into this issue where connect would fail.
1. I have disabled TLS peer verification...
We have a running project with nRF52840 + S140 7.2.0 - SDK: 17.0.2 + Bootloader.
I need to change the size of our bootloader in a production environment. This update must...
Hello,
We are currently certifying our module for Verizon in the US. As such, we are updating our software to work with MFW v1.3.0 and the corresponding NCS version v1...
Dear Nordic,
we developed firmware based on S112 and SDK 17.1.0. We have a problem with poweroff routine: at poweroff the status LED is ON.
this is part of our circuit...
Hi Team,
I am using nRF52840 on our custom board. I have enabled SMP for DFU and SMP image management in my build. DFU was successful for the 1st time but when I try to...
Hi,
I have my programming environment set up to use the nRF Connect SDK through VS Code, as the most recent documentation suggests. I can successfully build and flash code...
Hi ,
How we can achieve the right and left align for the data buffer register for the nordic as well as zephyr ? any sample example where this option we can achieve.
