Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hello,
I developed a code for nRF52840 Dongle to publish data on mqtt-sn topics (I'm currently using Nordic SDK for Thread and Zigbee). I need to know what are the limitations...
I'm working from the https://github.com/Martinsbl/nrf5-mpu-examples/tree/sdk13/nrf52-mpu-easydma-using-gpiote-and-registers example and the DMA portion is working splendidly...
I am trying to build the nRF Connect SDK project "at_client" that is provided with the IDE. I also tried the asset_tracker project with a similiar result.
This is my first...
i use a thread to save fil like below ,and find can not save file in sd card ,sd card SPI test ok . before enter in loop. close fil and reset system can save fil in sd card...
The first bug : I believe that the target level argument for the definition of the transition callback should be of type int16_t instead of the unsigned version since it is...
I'm trying to add a sensor driver to my project based off of Zephyr's sensor driver for adxl372. I can't figure out how to get the Kconfig file in that sensor folder to show...
Hi Nordic team,
I'm struggling with an issue where my chip wakes immediately after calling sd_app_evt_wait() - specifically if I call app_timer_start() before the wait for...
Hello, We are looking for production automated current measurement using your product Power Profiler Kit II. Is it possible to interface product using serial/commandline/python...
I wonder if anyone else has seen this issue. There are a few posts that seem to point to using nrfjprog to restore the board, albeit for nRF52. But nothing I have tried allows...
I need to do batch DFU updates, and the pc-ble-driver/nRF Connect Firmware combo is too unreliable for my needs. I would prefer to just use the wireless transciever built...
Hello,
I am using SDK 17.0.2 and want to use Memory Manager Diagnostics .
I have added to my project's sdk_config.h the following :
#ifndef MEM_MANAGER_ENABLE_DIAGNOSTICS...
Hello community,
I have been working on nRF BLE module. I want to make a project that has a small relay control for an appliance. The device will be connected to a mobile...
Hello guys, the USB controller of nRF5340 requires a voltage on VBUS pin.
1. Can nRF5340 be damaged if VBUS voltage rises into its valid range while the device OFF (VDD...
Hi,
I am using NRF52840 development kit and using s140 softdevice for bluetooth services. When I load the softdevice hex file and later load the Firmware hex file, I am...
