I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
HI
I used NRF24L01 module in direct mode and chose 250kbps in configuration
In TX mode : whether the data from MCU to module has to be send through exact 250kbps?
Dear Sir
I am trying to work with the ADC .
Attached a code
I get the lines
00> Adc sample 13772 00> Adc sample 13772 00> Adc sample 13772 00> Adc sample 13772...
Hi Nordic Team,
Some time facing Connection issue in Mobile app and some time device advertisement is not getting in app.
I am using below chipset and configuration. ...
Dear all, I try to self provision device by it self following steps below: Step 1 : Bind key Step 2 : Subscribe to topic
Step3 : Set publication topic
Step 4 The main...
I am having issues running GPS and LTE concurrently on the nRF9160DK and am wondering if the rootcause is an incompatibility between modem FW v1.2 and hardware v0.9.0. I am...
Hello,
With regards to the HID Keyboard Example,
1) Is it posible to disconnect from the central side (ios)? I would like to be able to disconnect as follows:
But...
Hi,
I have just started using the Nordic SDK (nRF5_SDK_15.2.0_9412b96) and am developing a low power application for a custom PCB using the rf52840.
I am developing...
I can read the spi flash id by the other mcu with the above code, but can not read correctly by
nrf52832, is there something wrong with my handle?
SPI FLASH ID 0E 40 13...
Hi!
We experience some problems with DFU, and while looking through the code, I saw the code copied below.
This is from the file dfu_req_handling.c from SDK14, and my...
Hello everyone,
I am programming my dongle(nrf52840) with my Dk. To upload the code I click on download "solution_name" in the target menu, it works fine for example without...
I am using NRF52840 Dongle to scan all the BLE advertisement packets.
I wish to scan for the BLE advertisements packets only from a particular device using the whitelisting...
hello all,
i am trying to add ble app uart feature in other ble app project. so i am trying to change those defines variable, NRF_SDH_BLE_GATT_MAX_MTU_SIZE & NRF_SDH_BLE_VS_UUID_COUNT...
1. In the ssdk:ncs v1.3 Example: in 10_hello_world_clock_gettime, test function: clock_gettime (CLOCK_MONOTONIC, last_action_time);
The following error occurred at compile...
Hello,
nRF52811, SDK16.0, Softdevice7.0.1
We had developed our application based on nRF Blinky Android sample app for nRF52840. Now we want to port same app for nRF52811...
Hi,
I would like to ask if it is possible to use both Radio and NVMC at the same time (no SoftDevice)?
My scenario:
Start Radio and configure RX mode.
Write/erase...
