I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hey there,
I am new to the community and I would like to looking for more than one cell. As I readed in another thread, it was possible with %NBRGRSRP a few month ago. ...
I was looking through documentation and I noticed that in OPS v0.7.1 the cold start was stated to be -144dBm. In PS v1.1 it calls out -142dBm. Can you explain why they are...
Hi!
I have BMD-350 -A-R and I want to program this by using SWD pins (SWCLK, SWDIO, GND Detect, and VTG) of Nrf52Dk . I make all the connections properly but for some reason...
Hi,
for evaluating purposes I'm trying to send quite big amount of data (100 kB) via socket interface. Sending proceeds fine until approximately 60 kB is transmitted. After...
Hi,
when powering up the nRF52840 PDK its interface MCU LED is blinking fast and the board is not recognized. I've tried to update its firmware by putting the board in bootloader...
On some android phones we have observed that if we try to scan using nRFToolbox for nRF51/ nRF52 controller advertising with UART they do not show up in the scan list. But...
Hello,
I am developing a wireless sensing device using the nRF24L01+ module and I'm planning to use a u.FL connector in my design. I can't seem to find any manufacturer...
Hello,
I am trying to test BLE with SAADC, UART function.
I am complete the ADC test and UART part.
So now, I want to SAADC with BLE and BLE with UART.
The whole connection...
Hi all,
I tried to follow this tutorial to be able to use GDB as debugger but failed right in the beginning because JLinkGDBServer could not connect. Here's the log I get...
Hi , i am using the nrf52dk and i have a switch statement that depending on the case there is a set of enum and i would like to utalised the push button to increase/decrease...
sir, i am attempting to compile a solution from github(nrf calender) but i could n"t.Tell me where should i put the file and how to compile to make it work??
Hello,
I have a question: how can i make applications for Nordic Thingy:91, and upload them to it? (I am a total newbie when it comes to Nordic products and IoT, i am not...
Hi All,
I am developing one project and there we are using ADC (i.e., SAADC in nRF). I have designed the hardware where I am using Capacitor ( C14, 2.2µF) which is connected...
Hi. I have a nRF52840 setup using the PWM driver, and it is outputting a 50Khz pulse 50% duty cycle.
How do I modify the sequence values so that I can modulate this 50Khz...
