Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
I cannot flash the nRF52840 Dongle using Programmer 4.3.0 with hex file sniffer_nrf52840dk_nrf52840_4.1.1.hex.
The option for writing is grayed out. =
- python...
While developing, I usually connect to the Serial COM Port to see my print statements.
However, when the devices crashes, only "*** Booting nRF Connect SDK v2.5.1 ***" is...
I've got a project that I'm going to want to do DFU through the UART, and in order to transfer files in a follow-on activity, I want SMP running in the application. Therefore...
We're trying to connect to our Azure Iot Hub using the Azure Iot Hub library provided by Nrf Connect Sdk 2.6.0 (without DPS). We're currently using the evaluation board to...
Hi,
I went through the Nordic Academy nRF Connect SDK Fundamentals - Serial Communication. I tried the exercise program where LED1, LED2 and LED 3 are toggled by pressing...
Hi Support Team,
Have a nice day.
Board : NRF5340DK
Python version : 3
nRF Connect SDK version 2.6.99
We are selecting the NRF5340DK for development purposes and...
I want to send the data from internal sensors via ble from thingy91 . not by usb , and by the way i can't by esim because im from tunisia and the lte-m does not work here...
Hi,
currently I'm facing an issue with the power consumption of my pcb. The idle power consumption is at about 20 µA. After initialising the UART it goes up to over 1 mA...
Hi,
I want to connect X-NUCLEO-NFC08A1 with ST25R3916B to nRF5340 board by adding a SPI node to device-tree source. After compiling and flashing the board, triggering interrupt...
Hi all,
NRF52832 NRF Connect 2.6.0
We need to configure interrupts on a GPIO on both edges. T here are several topics recommending to use GPIO_INT_TRIG_BOTH instead...
I'm getting started with nrf52840DK.
But when i connect my USB i get this error message:
i saw in this topic that when i press on the boot/reset long press when turning...
Hi all,
Could anyone share a code example for sending sensor data over BLE using the NUS Service in Zephyr RTOS? I'm new to this field and struggling to get data from the...
Hi
I use nRF7002-DK, SDK:Ｖ2.5.2 with zephyr driver, I need to send recieved data or command from uart, data type is using with hex byte array to send, from example , the...
Hi,
Because I wanted to add custom features to mcuboot, I had to use custom mcuboot.
I also used sysbuild for multi-image building.
The documentation tells me that...
Hello,
I am currently working with the nRF5340DK kit.
For my project, I need to incorporate some additional custom checks/code into the project's bootloader(MCUBoot)....
