When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
For the nRF9151-LACA-R, I cannot find the flatness parameter in its datasheet. Can you help confirm the flatness?
For the nRF54L15-CAAA, the datasheet shows A3 (0.03...
The MCP server requires authentication. To complete the setup, you'll need to: 1. Get an API key from Nordic Semiconductor / Kapa.ai 2. Reconfigure the server with the auth...
Hi All,
My leds on the custom board wont get recognized. Keep getting this error.
A bit of strack trace:
Device tree:
I think I am missing something...
Hi,
We're coming to the end of prototyping a project on the Thingy91X and are fine-tuning the power management. We have been able to implement a simple demo on the nrf9151dk...
Hi Support Team,
Our product is based on nrf5340 and ncs V2.5.2. I developed a Windows application(based on .NET8.0 and Windows SDK11) to provision and configure the system...
Hi, I'm struggling to setup an application on the nrf54l15dk to control the nrf9151dk SLM over UART.
I have done the Cellular IoT Course and successfully controlled the...
I'm trying out the GNSS sample for the nRF9161 DK. I am trying to enable minimal assistance, but I get an error message with error code 65536: *** Booting nRF Connect SDK...
Hi,
Can MCUboot be used as a second stage bootloader (an application from the Secure DFU Bootloader over Serial Link standpoint) to be DFU'ed to existing devices which now...
Is it possible for users to regenerate the nRF9160 GNSS factory almanac data from public sources?
https://github.com/nrfconnect/sdk-nrf/blob/main/samples/cellular/gnss...
Hel lo, I am us ing a custom nRF5 2832-based b oard that has no DCDC circu itry (LDO onl y). What happened in NCS v2 .5.1
After power-on, the system did not st art (e...
Hello,
I am trying to measure a fast, impulsive signal from an amplified analog microphone using an ADC pin on the nRF54L15-DK. When I read the same signal using a 12-bit...
Our production facility has some concerns about using the OTP parameters. Specifically, they are concerned about writing the wrong value and then needing to scrap the device...
Hi,
We are developing a product based on nRF5340(ncs 3.1.0) and using MCUboot for OTA updates of both app core and net core.
During an OTA update, the following issue...
Hi Team,
I am working with nRF5340 and have a few clarifications regarding SWD protection (APPROTECT / ERASEPROTECT).
While the application is running, is it possible...
We have an unusual issue.
We are using the nrf 17.1 SDK for a custom board with the nrf52840 in tickless idle mode (RTC1) - using the available port_cmsis_systick.c for...
