When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I am using ncs 3.3.1 in visual studio code. I created a custom board in the following location :
D:\hpgsystems\NSOC\nboards\boards\emtecSolutions\ppbr_rev2
The board...
Hi Nordic support:
We previously submitted a case about OTA testing in CMW500 connection mode. Following is that case:
We tried OTA testing with the CMW500 connection...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hi,
I'm about to develop a custom board with nRF52840 IC. For a first test I need an external antenna. I modified a dongle for a first proof of concept. I removed the antenna...
Hello,
We are trying to assess signal quality while synced to a BIS and we would like to use the RSSI values. RSSI values do show up when scanning and at least in the...
Hi,
I am using two nRF52833 devices with the nRF5 SDK. They are paired and bonded to each other. Occasionally, I encounter the following error in peer_manager_handler :...
I am looking to figure out my current consumption with an NRF52832 chip. I have the NRF chip running at 3V using UART, SAADC, BLE and SPI. The chip is constantly reading some...
I am developing an ESL proof-of-concept based on the Nordic Bluetooth ESL reference architecture and transitioning toward a small-scale PoC production (≈100 tags) . I have...
Hi,
I have a couple of questions on migrating from Partition Manager to Devicetree since a particular example was not provided. Following the procedure in the SDK v3.3.0...
I have a nRF54L15 firmware built on NCS v3.0.1, with image encryption enabled in mcuboot. Firmware needs to be updated to new version built on NCS 3.3.0.
In NCS 3.0.1, image...
Hi folks,
I am working on an nRF52840-based custom board using nRF Connect SDK v3.2.4 and have observed an issue related to runtime power management and PWM.
Environment...
I am using an nRF5340 DK (PCA10095) running the direction_finding_connectionless_tx sample from nRF Connect SDK v3.3.1 as a CTE transmitter for a Bluetooth AoA direction finding...
Hi, is there a sample using nRF7002 on nRF54LM20B SQSPI (or could you share an appropriate devicetree)? I have been successful using the nRF54LM20 DK + nRF7002 EBII combination...
Hello,
I've been working on a feature lately that involves writing the OTP registers in UICR on nrf54L15; after writing the registers I also wrote the protected value (0x50FA50FA...
Hello, we are having issues with using the nrf9151DK as a programmer for our own custom nrf9151 board. As the board seems to be locked, we tried to unlock it using the nrfutil...
