Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
is there any reference code to enable DCDC converter in nRF Connect SDK (NCS)?? (> v2.0.0)
I found some API, such as nrf_power_ dcdc en_get(...) or nrf_power_ dcdc...
Hi,
We have developed a customized board for use in a gateway. We would like to have a working bootloader on that board but it looks like it is almost impossible to make...
I'm working with the OpenThread CoAP protocol in the nRF Connect SDK 2.0.0. I started with the samples:
\ncs\v2.0.0\nrf\samples\openthread\coap_client
\ncs\v2.0.0\nrf...
Hello,
I have added service data to my advertising_init function, however it does display when looking at the nRF Connect app. I'm not sure why it doesn't show as it's similar...
1. The code uses a value 0xFF55AA5A to identify the adv packet as the one that supports distance measurement. Is this value checked by lower layers?
If not - why not just...
I can successfully perform a DFU of my BLE device via the Nordic "nRF Connect" App using a nRF52 DK. I'm trying to do the same via nrfutil CLI, now running into an issue:...
Hello,
I'm working with the nRF Connect NVS module on the nRF9160. Every time there is a read/write to NVS the messages:
I: 3 Sectors of 4096 bytes I: alloc wra: 0, 668...
Hello With Zbus being added to Zephyr, are there plans to carry on support for the Application Event Manager and the CAF or switch to using the Zbus system in future releases...
Hello,
I am new to the microcontroller development club and have recently obtained a nRF52 DK kit. I am using the new nRF Connect SDK and have the Arducam OV5642 camera...
Hi there,
We have developed a family of BLE products based on the NRF52832 using it's maximum TX power 4dBm.
We have a strong push for increasing the communication range...
I have a simple application running on our custom board based on nRF52840. Our board does not have any uart pins connected so we use RTT exclusively for console I/O. I attempted...
Hi! I am trying to use the Power Profiler app on my Windows computer, I have used it on another Windows computer, and it worked fine. Now, when I try to open the PP app, it...
I’m working on a project trying to characterize the range (given a certain transmitter and environment) on the BLE 1 mbps PHY. I’m using a few nRF52840 dongles to do this...
Hi,
I am evaluating nRF5340 audio dk with CS47L63 DSP. My goal is to find out the MCU processing consumption for LC3 codec what is MCU processing power left for the application...
Hi,
I am writing a program that sends numbers counting up sequentially from my dev board to my phone on 500ms intervals. I used the ble_app_uart example as my base. I am...
